Search results

  1. S

    Hacking Hardware Wifi error 2110-1118 after HWFLY

    But there is a mail notification :) I didn't solve this issue.I've taken that Switch to another guy who works with electronics,he told me that the problem was wifi IC.So who knows,maybe it did broke for some reason. Now I have done more then 200 oleds.Instead of using small wires and pico,I...
  2. S

    Hacking Hardware Wifi error 2110-1118 after HWFLY

    Hi,I've done more than 15 consoles with Picofly and Hwfly,and this one is a pain... Everything was working before modding,and now bluetooth is working,but Wifi gives 2110-1118. Switch is OLED. Searching over the internet,some people are saying that those SMDs left from APU can be ripped when...
  3. S

    No Wifi on switch after Hwfly install - 2110-1118 Error

    Can you please describe how did you fix it?Where are the lines going?They are going below APU,so I can't see where are they going next.My SMDs are ok after doing HWFLY,I don't know what happened.
  4. S

    Hacking Hardware Picofly - 2 yellow lights problem

    I put the USB back with a hot air and a little bit of soldering.It shouldn't be hard.You need a boot switch also.
  5. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    Is it possible that I fried something on board with SMD 4700 Resistors?I made a mistake when ordering them,and bigger mistake soldering them...Removed all the wires and nothing.I got 3.3 on middle of the board when pushing power button,but also got short on capacitor down from APU (Switch...
  6. S

    Hacking Hardware Picofly - 2 yellow lights problem

    Update 2: The problem was 2.72 update.DO NOT USE IT.2.73 works fine.
  7. S

    Hacking Hardware Picofly - 2 yellow lights problem

    Hi, I have modded 4 consoles with Picofly (RP2040 Zero),and this one gives me headache.Already done 2 OLEDs with no problem. So when powering on,it's normal blue,then it goes 2 yellows and boots in OFW.Firmware is 2.72.From new FW readme,it's the RST problem,and usually everyone is having DAT0...
  8. S

    Hacking Nintendo 3DS: new Firmware update (Ver. 11.7.0-40)

    I can confirm that ntrboot is working on 11.7 with R4 SDHC 2017 (o3DS XL).
  9. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    Can somebody help me. I had Startech FCREADMICRO3 and done reading nand from N3DSXL. Reader later died (it was getting hot when attached on usb),and I didn't write patched_nand. Bought another one Startech and done three 3DSXLs,but it won't recognise N3DSXL (the first one I mentioned). I'm...
  10. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    CLK point was damaged.R96 fell off.If there is no R96 on motherboard,3DS is getting blue screen.If you solder R96 (with no resistor),3DS turns on. I was asking is it important to have R96 for 3DS to read cartrige. Then I realised that I was making a mistake...3DS is USA version,so of course it...
  11. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    I mange to damage R96 (or maybe it's R94) on O3DS where CLK is going.It fell off.Turning on 3DS,without it,shows blue screen,but soldering both sides on it,turns on,but it won't read cartriges. My question is-Is it important for reading cartriges?Because I can't put 2 right pins back on cartrige...
  12. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    Alternate CLK point didn't work.It's much easier with that one below cartrige slot.Now,it's ok ;) Also the CLK point is DOWN,on first screen it shows it's up and down. Another tip,if you're modding more then one 3DS,be sure to delete autofirm folder and extract it again for the second mod.Some...
  13. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    Hey guys,I've succesfully modded O3DSXL,now I'm trying to do O3DS. I know that my SD reader works with XL,but something is wrong. I've checked connections 10 times,everything is ok,even the hard CLK point. I've noticed that if the GND wire is on the right pin,3DS will boot with blue screen,but I...
  14. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    Thanks for reply. I found out what was causing the problem.NAND should be NAND.BIN not NAND.IMG which Win32DiskImager created.So now Autofirm created new NAND.BIN (with new date and time) and it created backup_nand.bin.
  15. S

    Tutorial NAND Dumping 2DS/3DS/3DS XL/N3DS/N3DS XL!

    I can confirm that 5.25 Media Dashboard reader is working (internal),just disable in device manager - Universal Serial Bus controllers - Reneas USB 3.0 (Microsoft),USB Mass storage device and in portable devices disable volume for SD cards,then insert SD card,turn on 3DS and enable those 3...
  16. S

    Hardware 3DS XL Black screen with backlight on

    Hi, my 3DS XL had a broken upper screen.Bottom screen and touch were working. I replaced upper screen with new one and I got a black screen with backlight working. Sound is also working. I can use touch screen but I can't see anything. I placed another motherboard (from Japan),and everything...
  17. S

    Gaming DSi won't start up,need help

    Yes,it had a problem before I took it apart. I don't know the details,but I don't see any sign that it was in the water. Don't know about falling on the floor,there are no traces. Replacing the motherboard is expensive and there is no guarantee that it will work. If I don't find the solution,I...
  18. S

    Gaming DSi won't start up,need help

    Hi,I fixed some NDS Lites before and this is the first time I opened DSi and can't fix it. The problem is that when it turns on,both screen flashes and also blue light,then it quickly shuts off. First thing is of course-checking fuses. Both of them are ok. DSi is charging battery,on Multimeter...
General chit-chat
Help Users
    Psionic Roshambo @ Psionic Roshambo: I really need to dig out my USB Wii sensor bar and experiment with Wii emulation and synching...