Recent content by jetuaime81

  1. J

    Switch 1 v2 right joycon issue

    I haven't tried removing the joycons, I will try that seems to be the simplest way. But i did try a different joycon and it was the same. In this experiment i learned that the left has more range than right by about 1 to 2meters. I had changed tempered glass and did press hard to remove bubbles...
  2. J

    Switch 1 v2 right joycon issue

    Hi, I have a switch 1 v2 (hac-001 (001)). It has a weird problem that the right joycon stay connected but becomes unresponsive for a few seconds. The left one performs well and the wifi signal is also good, so I doubt it's the wifi ic. There is no connection drop. Also attached to switch both...
  3. J

    Switch right joycon weird issue in wireless

    .
  4. J

    Switch right joycon weird issue in wireless

    sorry switch 1 post. Admin please delete. Sorry again.
  5. J

    Ps2 50004, green then red light; PS003 fuse blown

    Ps2 50004, on power button goes to green and immediately to red. Found PS3 blown; the other side of the fuse is showing 1 ohm. The fuse is 72V, 2.5A rating. Any idea please share
  6. J

    Confused about updating nintendo switch

    Hey guys, Suppose I have a switch on some firmware and i update it using ofw and connecting to internet, the fuse will get updated. After this I have to delete atmosphere, bootloader and config folders and copy paste the updated ones. Will this be enought to get the emummc to work because i...
  7. J

    Hardware ps vita 2000 touchpad ribbon pulled off

    hi all, i accidentally ripped off the touch pad ribbon and was wondering how it was attached. it wasnt soldered and was basically glued down, how does this work and is there anyway to fix it back? its very difficult to source a replacement and also an expensive affair, so i would like to try...
  8. J

    Hardware Nintendo switch busted ram replacement

    Hi. I have an oled switch that had a max77812 ic busted. I replaced the ic (from AliExpress) and both the memory got damaged i think, showing short to ground on one of the inductor and heatspot on both memory when injecting 1v. k4u6e3s4aa-mgcl, the ic model is this. Does anyone know memory...
  9. J

    Hardware Switch oled short on phase 3 MAX77812 ic

    Injected voltage (1v), 1 ram ic and apu getting warm. Removed the ram ic, still there is short. I guess the apu is toast.
  10. J

    Hardware Switch oled short on phase 3 MAX77812 ic

    I have an oled switch board it's max77812 ic was getting hot. Replaced it but there is a short on the phase 3 I think. As circled in photo. I removed all caps on it but still there is short. Where does this go and how to go about fixing this?
  11. J

    Hardware Switch oled kamikaze fail

    Thanks. I have seen a few videos on youtube on fail recovery. But yes, I got lucky i guess, I had very uneven grinding and also the fact that there is only ground layers in this area on inner layers also helped. The pointed 0.5mm bits are more like a drill bit than a grinding bit, maybe it's my...
  12. J

    Hardware Switch oled kamikaze fail

    @thesjaakspoiler I was successfully able to boot the console. Thanks
  13. J

    Hardware Switch oled kamikaze fail

    Oh.. that's a whole lot of work, I don't know if i should try. let me do some research on 1 bit mode, first time I'm hearing about this thanks for pointing me in the direction. I was just thinking of installing a dat0 adapter and seeing if I get continuity on the point with the arrow in my...
  14. J

    Hardware Switch oled kamikaze fail

    Thankyou. I have been through multiple posts and these files of layers. Unfortunately, after a certain point I am completely lost. I didn't understand the emmc part. Is it something that would make this switch turn on again?
  15. J

    Hardware Switch oled kamikaze fail

    hi. i have failed miserably in my kamikaze attempt. I have taken some diode readings (red probe on ground). Is there any way to recover this? Also the point marked by the arrow seems very big, which has got me real confused as to what layer i am on now. I have the necessary tools for joining...
See more