Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

[mrdude]

Sounds like a SXOS prob to me... What happens under AMS? Same thing?

Yes same thing for that as well - I've attached my uf2 in the above post - can you test it for me please, so I can rule that out as an issue? thanks.

 

[mattytrog]

I can. But you may have a bit of a wait.

I`m working on the file-based emuMMC. Made some changes and got it booting.

Getting an exception though.

 

[mrdude]

I can. But you may have a bit of a wait.

I`m working on the file-based emuMMC. Made some changes and got it booting.

Getting an exception though.

No worries, there's no rush - this has always been like this for me. I'm unsure if it's a firmware/nand issue or wiring issue with my chip. Nobody else seems to have those issues. It's not a major deal though as I can still install via usb using my switch hub and usb drive via SX installer

I'm using a usb c - otg cable. If that makes any difference?

 

[rodrigues14]

@mattytrog you can fix rcm-x86 to search payload.bin on sd? because when use this UF2 file chip keep on and can't use Goldleaf usb install, i try all uf2 disponible, only 1 work fine but kill joycon on right side ( i refeer to switchboot uf2)

 

[mattytrog]

@mattytrog you can fix rcm-x86 to search payload.bin on sd? because when use this UF2 file chip keep on and can't use Goldleaf usb install, i try all uf2 disponible, only 1 work fine but kill joycon on right side ( i refeer to switchboot uf2)

OK. Which one worked fine?

 

[rodrigues14]

OK. Which one worked fine?

this one https://github.com/mattytrog/Switch...UF2/REBUG_SWITCHME_SWITCHBOOT_PART2_V135a.UF2
won't "kill" usb but "kill" right joycon on portable mode

 

[mattytrog]

this one https://github.com/mattytrog/Switchboot_PART_2/blob/master/Switchboot-V1.3.5/Switchboot Part 2 UF2/REBUG_SWITCHME_SWITCHBOOT_PART2_V135a.UF2
won't "kill" usb but "kill" right joycon on portable mode

I thought I had fixed RCM-X86. Will take a look.

 

[rodrigues14]

I thought I had fixed RCM-X86. Will take a look.

same link?

 

[mattytrog]

RCMX86 internal

 

[rodrigues14]

RCMX86 internal

this one you mean https://github.com/mattytrog/Fusee-UF2/blob/master/Fusee_UF2_V3/RCMX86_INTERNAL_FUSEE_UF2_V3.UF2 ?

kill joycon on portable mode too

 

[mattytrog]

this one you mean https://github.com/mattytrog/Fusee-UF2/blob/master/Fusee_UF2_V3/RCMX86_INTERNAL_FUSEE_UF2_V3.UF2 ?

kill joycon on portable mode too

Sounds like your reset button is stuck down on the chip or something.

I am running it currently on my bench board and two other consoles.

Any chance of a picture of your install sir?

 

[rodrigues14]

sure i will open the console, you think maybe is my magnet resistor?

Sounds like your reset button is stuck down on the chip or something.

I am running it currently on my bench board and two other consoles.

Any chance of a picture of your install sir?

--------------------- MERGED ---------------------------

--------------------- MERGED ---------------------------

 

[mattytrog]

Your wiring is incorrect sir.

The joycon strap is incorrect.

Also please reflow the GND and RESET pad with flux. They look like a bit like "pigeon shit" as we say in the trade.

Apart from that, good job.

 

[rodrigues14]

Your wiring is incorrect sir.

The joycon strap is incorrect.

Also please reflow the GND and RESET pad with flux. They look like a bit like "pigeon shit" as we say in the trade.

Apart from that, good job.

You mesmo os incorrect on chip? Because i follow the Guide in rcm-x86 Github

 

[mattytrog]

Follow this:

https://gbatemp.b-cdn.net/attachments/rcmx86-internal-final-jpg.154658/

You only need to connect the joycon strap. Things will be better then.

 

[rodrigues14]

Follow this:

https://gbatemp.b-cdn.net/attachments/rcmx86-internal-final-jpg.154658/

You only need to connect the joycon strap. Things will be better then.

You mean the BLUE one on diagram? Because the Orange one i have on my install

--------------------- MERGED ---------------------------

I see i solder on diff pad on chip is that the issue?

 

[mattytrog]

Solder the orange one to the correct point.

You have it connected correctly it seems on the Switch side, but it is connected to D0 on the RCMX86. This is incorrect. At least for my software anyway.

Connect to D2 instead.

 

[rodrigues14]

Btw the pidgey shit yoy reter ( i laungh so much )
Is hot glue down the chip

--------------------- MERGED ---------------------------

Solder the orange one to the correct point.

You have it connected correctly it seems on the Switch side, but it is connected to D0 on the RCMX86. This is incorrect. At least for my software anyway.

Connect to D2 instead.

Thank you so much for the help and sorry for bother you, i don't check your wiring os diff from rcm-x86 Github, thank you for the support and for you work on the scene

 

[mattytrog]

Btw the pidgey shit yoy reter ( i laungh so much )
Is hot glue down the chip

--------------------- MERGED ---------------------------




Thank you so much for the help and sorry for bother you, i don't check your wiring os diff from rcm-x86 Github, thank you for the support and for you work on the scene

No problem! Let me know if it is working

 

[MAMBO3000]

@mattytrog Hi friend i have a issue with trinket m0 im trying to update the switchboot but i cant access the bootloader im pressing the reset button twice like always but nothing happen im in switchboot 1.10 when i press twice the reset button the light turn red flashing fast and its supposed to flash but slowly.