Hacking Can't load SX after Emunand update

[Diego30k]

Hi,
I finally get my unpatched switch this week (OFW 4.1), then I did the following steps:

• Got MicroSD 64GB (Fat32 format)
• Booted SX OS 2.0.1 (I prefer to wait until a stable version)
• Created an Emunand (from 4.1)
• Checked Emunand was succesfully installed
• Updated Emunand to 6.1 using choidujournx

After the reboot I tried to boot RCM (jig + Volume + up) but every time I connect my switch to my PC (Tegra), suddenly it powers up and loads OFW

Why is this happening?

Thank you for your help =)

 

[GraFfiX420]

Hi,
I finally get my unpatched switch this week (OFW 4.1), then I did the following steps:

• Got MicroSD 64GB (Fat32 format)
• Booted SX OS 2.0.1 (I prefer to wait until a stable version)
• Created an Emunand (from 4.1)
• Checked Emunand was succesfully installed
• Updated Emunand to 6.1 using choidujournx

After the reboot I tried to boot RCM (jig + Volume + up) but every time I connect my switch to my PC (Tegra), suddenly it powers up and loads OFW

Why is this happening?

Thank you for your help =)

It sounds like your jig is not working.

 

[Deleted User]

It sounds like your jig is not working.

yeah

 

[The Real Jdbye]

It sounds like your jig is not working.

Sounds more like he hasn't actually turned the Switch on. If the jig wasn't working it would just boot normally when he pressed power.

Hi,
I finally get my unpatched switch this week (OFW 4.1), then I did the following steps:

• Got MicroSD 64GB (Fat32 format)
• Booted SX OS 2.0.1 (I prefer to wait until a stable version)
• Created an Emunand (from 4.1)
• Checked Emunand was succesfully installed
• Updated Emunand to 6.1 using choidujournx

After the reboot I tried to boot RCM (jig + Volume + up) but every time I connect my switch to my PC (Tegra), suddenly it powers up and loads OFW

Why is this happening?

Thank you for your help =)

So wait, how did you manage to boot SX OS if you can't get RCM to work?

 

[Diego30k]

Thank you to you all for you help, the solution was so simple:

• I tested that every time I connect my switch to my PC suddenly turns on
• I turned off my switch with the usb cable connected
• Entered RCM Mode (JIG + up/power)
• Emunand is working!

=)

 

[Zap2000]

Hi,
I finally get my unpatched switch this week (OFW 4.1), then I did the following steps:

• Got MicroSD 64GB (Fat32 format)
• Booted SX OS 2.0.1 (I prefer to wait until a stable version)
• Created an Emunand (from 4.1)
• Checked Emunand was succesfully installed
• Updated Emunand to 6.1 using choidujournx

After the reboot I tried to boot RCM (jig + Volume + up) but every time I connect my switch to my PC (Tegra), suddenly it powers up and loads OFW

Why is this happening?

Thank you for your help =)

Why use SX OS 2.0.1 ? The emuNAND just running from ur normal nand ?

 

[Diego30k]

Why use SX OS 2.0.1 ? The emuNAND just running from ur normal nand ?

I use 2.0.1 because acording to its official web site is the last stable version (2.4 is in beta and there's no link for 2.1,2.2 or 2.3)
The emunand is installed in the internal storage.