Tutorial
Updated
How to setup Emunand/ keep Sysnand online
YOU HAVE BEEN WARNED
Aiming of having Emunand in this topic is to max out Sysnand to play online while Emunand stays offline
IF YOUR SYSTEM WAS BANNED YOU'D STOP READING FROM HERE
> DO NOT check whether you're got banned yet by connecting to the Internet or so.
There is always at least a risk to get you banned or unlikely to brick your Switch.
YOU'RE AT YOUR OWN RISK
I TAKE NO RESPONSIBILITY FOR ANY DAMAGES OR BAN.
> Backup RawNand and BOOT0/1 using SX Bootloader, Hekate or any trusted tools out there
1. NEW EMUNAND
YOU HAVE TO RE-INSTALL ALL GAMES AFTER CREATING EMUNAND
> Backup all your savedata using Checkpoint or your trusted homebrew.
Follow these steps below
> Backup all your savedata using Checkpoint or your trusted homebrew.
Follow these steps below
This guide is valid until the next update of NSW firmware or SX OS.
CLEAN UP SYSNAND
UPDATE SYSNAND FIRMWARE
CREATE EMUNAND
UPDATE EMUNAND FIRMWARE OFFLINE
ENJOY WHILE IT LASTS
Aiming of having Emunand in this topic is to max out Sysnand to play online while Emunand stays offline
IF YOUR SYSTEM WAS BANNED YOU'D STOP READING FROM HERE
> DO NOT check whether you're got banned yet by connecting to the Internet or so.
There is always at least a risk to get you banned or unlikely to brick your Switch.
YOU'RE AT YOUR OWN RISK
I TAKE NO RESPONSIBILITY FOR ANY DAMAGES OR BAN.
> Backup RawNand and BOOT0/1 using SX Bootloader, Hekate or any trusted tools out there
1. NEW EMUNAND
YOU HAVE TO RE-INSTALL ALL GAMES AFTER CREATING EMUNAND
> Backup all your savedata using Checkpoint or your trusted homebrew.
Follow these steps below
- CLEAN UP SYSNAND
- UPDATE SYSNAND FIRMWARE
- CREATE EMUNAND
- UPDATE EMUNAND FIRMWARE OFFLINE (if needed)
to update your emunand to the latest firmware
> Backup all your savedata using Checkpoint or your trusted homebrew.
Follow these steps below
- CREATE EMUNAND
- CLEAN UP SYSNAND
- UPDATE SYSNAND FIRMWARE
- UPDATE EMUNAND FIRMWARE OFFLINE (if needed)
to update your emunand to the latest firmware
This guide is valid until the next update of NSW firmware or SX OS.
CLEAN UP SYSNAND
Skip this step if your Switch is a brand new one or never ever been hacked.
+ Unnecessary steps but it will let you feel safer
+ Factory Restore Settings
> This will clean all ticketblob and error logs
Stay OFFLINE
> Settings > System > Factory Restore Settings (or System Initializing)
> Say NO when asking Internet connection
> Press on on the red button after all to restore.
+ Unnecessary steps but it will let you feel safer
Access NAND using PC
What you will need
- biskeydump
https://files.sshnuke.net/biskeydumpv6.zip
Run the payload and write down (or scan QRCode) Bis Key 2
BIS KEY 2 (crypt): NUMBERS
BIS KEY 2 (tweak): NUMBERS
- memloader
https://files.sshnuke.net/memloaderv2.zip
Copy *.* in [sample] folder to SD and plug it in the Switch
Run the payload [memloader.bin]
Unplug any USB cable
> Choose emmc line
> Plug USB C <> USB A cable to the Switch and PC
- HacDiskMount
https://files.sshnuke.net/HacDiskMount1055.zip
Run the tool under Administrator permission
> Open Physical Disk > Choose Linux line
> Double click on SYSTEM and fill BisKeys2 in the small table on top
Crysto > BIS KEY 2 (crypt): NUMBERS
Tweak > BIS KEY 2 (tweak): NUMBERS
> Press on [Test] > you will get OK! Entropy
> From Drive Letter table > Choose a drive disk, N for example.
> Press on [Mount]
Install driver if needed.
Acess N drive from My Computer
+ Clean Ticketblob
> access save folder
> Copy 80000000000000e1 and 80000000000000e2 to your PC.
> Delete them in save folder
+ Clean Error Logs
> access save folder
> Delete 80000000000000D1
> Press on [Unmount] and unplug the USB cable
> Press on [Power] button for 15s or so to reboot the system
What you will need
- biskeydump
https://files.sshnuke.net/biskeydumpv6.zip
Run the payload and write down (or scan QRCode) Bis Key 2
BIS KEY 2 (crypt): NUMBERS
BIS KEY 2 (tweak): NUMBERS
- memloader
https://files.sshnuke.net/memloaderv2.zip
Copy *.* in [sample] folder to SD and plug it in the Switch
Run the payload [memloader.bin]
Unplug any USB cable
> Choose emmc line
> Plug USB C <> USB A cable to the Switch and PC
- HacDiskMount
https://files.sshnuke.net/HacDiskMount1055.zip
Run the tool under Administrator permission
> Open Physical Disk > Choose Linux line
> Double click on SYSTEM and fill BisKeys2 in the small table on top
Crysto > BIS KEY 2 (crypt): NUMBERS
Tweak > BIS KEY 2 (tweak): NUMBERS
> Press on [Test] > you will get OK! Entropy
> From Drive Letter table > Choose a drive disk, N for example.
> Press on [Mount]
Install driver if needed.
Acess N drive from My Computer
+ Clean Ticketblob
> access save folder
> Copy 80000000000000e1 and 80000000000000e2 to your PC.
> Delete them in save folder
+ Clean Error Logs
> access save folder
> Delete 80000000000000D1
> Press on [Unmount] and unplug the USB cable
> Press on [Power] button for 15s or so to reboot the system
+ Factory Restore Settings
> This will clean all ticketblob and error logs
Stay OFFLINE
> Settings > System > Factory Restore Settings (or System Initializing)
> Say NO when asking Internet connection
> Press on on the red button after all to restore.
UPDATE SYSNAND FIRMWARE
Skip this step if your Switch is up to date.
Complete the system initializing
> Connect Wifi to the Internet
> Optional > Create a new account and link it
> Settings > System > System Update
> Update your system to the latest firmware
Optional > Factory Restore Settings while staying ONLINE to make it completely cleans up.
DELETE ALL WIFI CONNECTION AND STAY AIRPLANE MODE.
> After creating Emunand, it must have NO CONNECTION.
Complete the system initializing
> Connect Wifi to the Internet
> Optional > Create a new account and link it
> Settings > System > System Update
> Update your system to the latest firmware
Optional > Factory Restore Settings while staying ONLINE to make it completely cleans up.
DELETE ALL WIFI CONNECTION AND STAY AIRPLANE MODE.
> After creating Emunand, it must have NO CONNECTION.
CREATE EMUNAND
SD card must be plugged in to the system in order to boot SX OS Bootloader Menu
> On SX 2.3 Beta, the Emunand will be created on the SD card, the SX's Nintendo folder is renamed to Emutendo so that it won't affect to the keyblobs that can wipe out data on SD.
> Boot to SX OS Bootloader Menu (payload.bin) by holding [Vol+] button
> Option
> EmuNAND
> Advanced
> [Copy USER partition to EmuNAND] > [YES]
The process will take about 30 minutes if the system is now empty.
You will get Success
> Back to the main menu (3 big buttons)
> Turn on Emunand (on top of the first button)
> Turn off the system
> On SX 2.3 Beta, the Emunand will be created on the SD card, the SX's Nintendo folder is renamed to Emutendo so that it won't affect to the keyblobs that can wipe out data on SD.
> Boot to SX OS Bootloader Menu (payload.bin) by holding [Vol+] button
> Option
> EmuNAND
> Advanced
> [Copy USER partition to EmuNAND] > [YES]
The process will take about 30 minutes if the system is now empty.
You will get Success
> Back to the main menu (3 big buttons)
> Turn on Emunand (on top of the first button)
> Turn off the system
UPDATE EMUNAND FIRMWARE OFFLINE
> ChoiDujourNX https://files.sshnuke.net/ChoiDujourNXv101.zip
> Copy ChoiDujourNX.nro to \switch\ in your SD
> Download new firmware update
> Place all files to a folder, fwxxx for example
> Run ChoiDujourNX form Homebrew Menu on Emunand
> Choose fwxxx folder
It will load all NCAs inside of the folder and will ask you
[x.x.x] or [x.x.x-exfat]
Choose one
It will continually analyze the data and will ask you
> Choose [Select Firmware]
It will read all the data from your chosen firmware
> Press on Prevent fuse burning (enable AutoRCM) to turn it off (we don't need AutoRCM when having Sysnand for online purpose), Press on Yes when it asks again.
If you'd like to have AutoRCM installed just leave it be.
> Press on [Start installation]
> [Reboot] > [Shutdown]
> Copy ChoiDujourNX.nro to \switch\ in your SD
> Download new firmware update
> Place all files to a folder, fwxxx for example
> Run ChoiDujourNX form Homebrew Menu on Emunand
> Choose fwxxx folder
It will load all NCAs inside of the folder and will ask you
[x.x.x] or [x.x.x-exfat]
Choose one
It will continually analyze the data and will ask you
> Choose [Select Firmware]
It will read all the data from your chosen firmware
> Press on Prevent fuse burning (enable AutoRCM) to turn it off (we don't need AutoRCM when having Sysnand for online purpose), Press on Yes when it asks again.
If you'd like to have AutoRCM installed just leave it be.
> Press on [Start installation]
> [Reboot] > [Shutdown]
ENJOY WHILE IT LASTS
Last edited by thaikhoa,
