Search results

  1. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    I was not using the switch for a month and put it in its box with 80% charge turned off and now when i boot the switch it automatically boots into ofw. The led only lights up as its saying success but no matter what i cant get into the no sd card logo. Can anybody help?
  2. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    i fixed the problem and it was not the soldering issue but an extra resistor on the pico w. i will post photos and a little guide for people who wants to use pico w for picofly.
  3. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    heating up the solder mask did the job and i removed all of the mask successfully and resoldered every wire. but the problem still continues. same error code as the last one and im sure the issue is not about my soldering skills as i've installed two more pico other than this one. any other ideas?
  4. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    How can i detect the bad wiring problem? I tested the continuity with the alternative soldering points and all of the points are connected without any problem. I cant desolder the wires and resolder them because i put solder mask on top of them.
  5. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    If i remove the pico w i can boot into ofw. I tried checking the connections again and now im getting one long three short pulses which means emmc init failure. Is there a fix for that?
  6. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    Its not actually GPIO0, its connected to the wireless chip's GPIO0. I manually cut the trace of the GPIO25 which is connected to the wireless chip and connected it directly to the led which worked! Now I get an error code of one short two long pulse. Its says poor wiring or dead CPU in the...
  7. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    Led works with Raspberry Pi Pico (without W) but not for Pico W. Its not RGB but with latest firmware there is no need for RGB. If I somehow trick the firmware to thinking its normal Pico it might work (or not).
  8. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    Tested Pico W today, the LED does not work and the switch does not boot with the pico w attached. Had to remove it in order for it to boot. If @rehius supports the pico w in the picofly firmware i will test it again and post the results here.
  9. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    i ordered 3 raspberry pi pico because other models are not common in my country but seller sent me raspberry pi pico w. is there any way to use this one by cutting it as normal pi pico?
  10. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    Did anyone tried these mosfets or have knowledge about whether they would work or not? IRFH8334, IRFH8318, IRFH3707
  11. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    But now you create another problem. What if A4 creates sc with A5? You need to create these test pads for every pin on that side so it can be tested properly if it sc.
  12. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    I set my soldering iron to 275C so i wont rip the pads. Next time i will try that method.
  13. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    i tried heating it up for long enough but then i thought if i heat it up for that long it might damage the solder balls underneath and soldering ground to the shield resulted same.
  14. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    You can use it. I also used this one.
  15. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    This is my second picofly install and its now with raspberry pi pico and mosfets. The ground point on the apu was not sticking to the wire so i used the apu shield as the ground point.
  16. X

    Wi-Fi and bluetooth range is extremely short on switch v2

    I bought a used switch v2 with wifi range issues. When searching for networks it founds every single wifi network that my other devices can detect but when it gets to connecting to them no matter what it cant connect to a wifi if its over 20-30 cm away from the switch. It was not a problem for...
  17. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    what mosfet did you use?
  18. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    After a little bit research on my local electronics stores i think FDS6690AS should be compatible with picofly. Can anyone let me know if they tried this mosfet already?
  19. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    So i think if drain to source voltage is 30V, continuous drain current is higher than 12A and if its N type mosfet i should be okay. Right?
  20. X

    Hacking Hardware Picofly - a HWFLY switch modchip

    I want to install picofly on a switch lite but without flex cable so i need to use mosfets. The most used one (IRFHS8342) is not available in my country so i need to pick another mosfet. What criteria should i be looking at in order to make sure the mosfet is compatible with picofly?
General chit-chat
Help Users
    SylverReZ @ SylverReZ: I used to play it on the iPad. +1