Search results

  1. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Yes glare from my camera is automatically a bridge. I did these with a microscope, there is no bridge. Fuck off. Fucking toxic piece of shit. Sent from my SM-N986U using Tapatalk
  2. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I already did that you moron. Don't you have a hobby? Oh wait, Nintendo sent you a c&d and I'm still making money. Must be with all that extra time you grief people online with 2 accounts to pat yourself on the back. And if you're such the genius, surely you know what's wrong instead of...
  3. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Go fingerbang your bf Izy. I know my soldering is solid and my bank account agrees. How immature and toxic. Sent from my SM-N986U using Tapatalk
  4. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I only have a multimeter. The v2 boots atmosphere and displays to a TV if docked. Sent from my SM-N986U using Tapatalk
  5. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    What points should I test? Backlight only, correct. Sent from my SM-N986U using Tapatalk
  6. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Soldering isn't the issue or else my failure rate would be higher than 2 out of ~40. The soldering is fine and unless youre s-tier, i dont want to hear that when its not the problem. And that's VERY constructive and conducive to the question at hand. What a great atmosphere we have here where...
  7. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Before you wanna be a dick, I'm using Flux and a Weller soldering station OR a pinecil depending. If you aren't gonna be helpful, fuck off. Not my fault you're Butthurt over your c&d. Says "janky" but then has this posted like all the solder is better and not even fused to the shield.
  8. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    Ive done them all a couple times before without issue. I even sell premodded OLEDs on the side and Ive never had an issue except beeding to redo a dat0. With Core and Lite, I've never had this issue until these 2. I can assure beyond a doubt that there are no shorts with the core as it's just...
  9. P4RI4H

    No LCD after HWFLY (v1 & Lite Install)

    I'm at my goddamn wits end with these things. Installed a HWFLY Lite and Core V1 for a FoaF, and now neither displays anything on LCD upon boot. The LCD cable was never unplugged and the batteries on both were unplugged immediately. If it was one time I would chalk it up to chance damage bit...
  10. P4RI4H

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    So last night I decided to clean up my wiring, and I trimmed and re-soldered everything on the Trinket. The random vol+ stopped. I have NO IDEA why because all that changed were wire lengths. I'll keep this in mind if it starts again. Thanks! Sent from my SM-N986U using Tapatalk
  11. P4RI4H

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Hey everyone, things are getting wonky again for me here. I had an issue before of Vol+ triggering that was solved with kapton tape. Well today I was re-shelling my switch and decided to hook up the joycon strap because I read that a dead battery+auto rcm can hurt the charge chip. I added joycon...
  12. P4RI4H

    OLED, permanent dat0, inconsistent boots?

    @OrganixXx No, I hadnt posted on twitter, but i did ask about voltages on reddit with Hynix. I have it permanently attached with reflow and its the 2 anchor version. Tried multiple adapters and always get same 2 readings .2 v apart. @randy_w yes, purple>orange like when it starts...
  13. P4RI4H

    OLED, permanent dat0, inconsistent boots?

    Recently installed HWFLY in OLED, The dat0 point always gets 2 values and always exactly .2v difference. Was told that with SK Hynixemmc, this is normal as long as I get successful glitches. However, training took ungodly long, to the tune of ~4 hours. Ive never been unable to get a single .6xx...
  14. P4RI4H

    OLED Hekate slow with SD

    I recopied the hekate payload files and it fixed the issue. Obviously they didnt copy correctly when extracted to SD for whatever reason.
  15. P4RI4H

    OLED Hekate slow with SD

    I just recently installed a HWFLY chip in my OLED, and without SD card, my switch boots instantly (<5s) and says no SD card which is expected. When I put payload.bin on an sd card and insert it, it takes nearly 30 seconds to boit to the attached screen and does nothing else. Any ideas...
  16. P4RI4H

    Tutorial HWFLY chips will brick your OLED. Here is how to avoid it

    Hey everyone, quick question regarding the Lite HWFLY on OLED. If i read this correctly, having the updated firmware mitigates the issue with OLED? Thanks Sent from my SM-F926U1 using Tapatalk
  17. P4RI4H

    Hardware PS4 Raspberry Pi host GoldHEN Update

    Forced a restart of the pi and shutdown PS4 both before trying, and it worked. It doesn't automatically restart so I'm thinking I probably pushed the new payload and tried to exploit without restarting the pi and it broke it permanently so even a restart after the fact didn't help. Can't be sure...
  18. P4RI4H

    Hardware PS4 Raspberry Pi host GoldHEN Update

    That's what I did, following the (somewhat vague) directions on github. I can see the appropriate bin in the folder after selecting goldhen on the bottom right, but it gives me this error after trying to exploit. Sent from my SM-F926U1 using Tapatalk
  19. P4RI4H

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Sure enough, the kapton under the chip fixed it. I never would've expected it to ground but I guess it does make sense. Wish I would've thought of that during installing and then I wouldn't have had to open it 37 times. [emoji1787] Sent from my SM-F926U1 using Tapatalk
  20. P4RI4H

    Hardware PS4 Raspberry Pi host GoldHEN Update

    I have a Pi Zero I use as a host from this github: https://github.com/PaulJenkin/PS4RaspberryPi I'm sure many of you use the same, and I hope that someone has a solution to my problem. When I try updating the GoldHEN bin using the instructions, once the exploit delivers the payload it says...
General chit-chat
Help Users
    Xdqwerty @ Xdqwerty: @K3Nv2, prove it