Recent content by jvv

  1. J

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    Hello guys, I've been out from this for a while. I've updated my trinket and the setup screen shows the following: Fusee_uf2 information. v6_110320 Following strap detected: joycon USB voltage: chip-based auto rcm mode active boot animation 2 selected screensaver is active However If I...
  2. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    pin 2 (new method 3)
  3. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I have method 3 without vol + wire. The power on reset is not placed under and board. I will give a try.
  4. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I guess the one I need is this Trinket_Legacy_Method 3 right? I have trinket M0 installed. Sorry, this has been changed a lot since August.
  5. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Good Morning guys, I was disconnected about this matter for a while. I am using method 3 and I would like to update my trinket with the latest version of Hekate. As far as I read in the previous post I have to take it from git. My question is: Witch one I should take? Cheers
  6. J

    Hacking RELEASE Kosmos - A Hekate CFW-package

    Works perfect switch doom with new 7.3. Amazing Job
  7. J

    Hacking RELEASE Kosmos - A Hekate CFW-package

    I have some issues running Doom. The only way I made it run is with ReiNX-SDFilesV731 deleting the fs_mitm.kip file. Is there a way to do the same with Hekate new release? Could someone explain the main duty of this kip module?
  8. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    It looks like Chinese people are working on the same https://es.aliexpress.com/item/Dealonow-reemplazo-reparaci-n-clip-para-interruptor-RCM-NS-cortocircuito-herramientas/32908068356.html. I've checked the diagram they provided and I found out that there are two points for joy-con pin 10. My...
  9. J

    Hacking RELEASE Kosmos - A Hekate CFW-package

    Thanks for the amazing job you are doing
  10. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    When you are in switch "Home page" of the firmware. They found out that the operating system’s internal name is Horizon, that it is an evolution of the Nintendo 3DS system software, and implementing a microkernel architecture. More info https://en.wikipedia.org/wiki/Nintendo_Switch_system_software
  11. J

    Hacking RELEASE Kosmos - A Hekate CFW-package

    Looks like new version has been released v7
  12. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I would like to ask another thing. In case I want to compile the code you provided is there any extra library I have to install in Arduino IDE? I've read in other post that if we would like to compile the source code we need to install extra libraries. Do you have any step by step guide? Cheers
  13. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I've changed the pin 2 to the correct switch point. I do not have any dock here as I'm not at home But I guess I could try with the PC because when I hat the wrong point it did not charge the switch when It was turned off. I will keep you posted. Again thanks to every one who helped me out ;)...
  14. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Ok I could see where the issue is. I will fix the problem. Wrong point on switch board. Thanks
  15. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Good morning guys! I’m confused of what happen with my pink wire. As far as I have checked the pink wire should go from pin10 joy con to pin 3 of trinket right? As far as I checked there is no bridge either usb or trinket usb pads. Could you please give me some lights here as I don’t know how...
See more