Recent content by DawnWorkout

  1. D

    Hacking Hardware After installing the Picofly (clone), it shows a pulse pattern I've never seen before and doesn't work.

    Rcm okay After attempting to work on the kamikaze, we have not been able to confirm the entry into the official firmware I'm sure there's nothing wrong with the installation
  2. D

    Hacking Hardware After installing the Picofly (clone), it shows a pulse pattern I've never seen before and doesn't work.

    I performed the Kamikaze mod and all the work and values are correct. The issue persists even after replacing the chip. I previously received advice regarding this problem, suggesting the addition of a resistor. I am planning to order an SMD 0201 type 100 ohm resistor. Unlike the RP2040 chip...
  3. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    It's the first time I've actually seen the installation of Resistance. Where should I connect the specifications of which resistance? My NAND is Toshiba emmc. All the devices I worked on before were Samsung and SK. Is this causing the problem? I've switched chips and tried installing again and...
  4. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Glitching the OLED switch after camikaze results in a *=* (short-long-short) situation. All diode readings are fine I've already successfully worked on the camikaze several times And I've seen an opinion that resistance should be added as a solution to a similar problem Where should I add any...
  5. D

    Has anyone tried replacing this socket inside the Switch Lite?

    Oh sorry I didn't know forum rules I will upload real picture again later
  6. D

    Has anyone tried replacing this socket inside the Switch Lite?

    It's a picture from a website I got the picture from the web because I covered the device.
  7. D

    Has anyone tried replacing this socket inside the Switch Lite?

    I finished installing the mod chip safely However, the left analog stick only moves up and down and doesn't work left and right. Replacing the analog stick and film didn't solve it either. Just a guess, I think there was some damage when taking out and putting the film in this socket in the...
  8. D

    I made a mistake before replacing the Lcd socket.

    1737035722 That's good news. I have a lot of difficulties with the lack of hot air station usage skills prior to installing this socket, but I will try again by purchasing an additional socket. Thank you.
  9. D

    I made a mistake before replacing the Lcd socket.

    I zoomed in on that part, but I can't find any remaining traces. I'm very concerned. 1737034953 I'm sorry, but what exactly does NC mean? Not connected? So if I ignore that part and try to fit the socket, will this machine be saved?
  10. D

    I made a mistake before replacing the Lcd socket.

    Switch oled soldering point One pin fell off while gluing lead to the soldering point with a lead tip Is it an essential element? If there's no chance I'm going to dispose of this machine... Socket replacement is too difficult It's easier to install chips....
  11. D

    Hardware Are there any alternatives to Oled D points?

    Hello The OLED has become a brick I thought D point was the problem. so I put a lot of scratches on the Oled D point When I connect the solder wire, it keeps getting solder short... Is there a temporary prescription to solve this problem? I have a similar problem and the LITE device is brick...
  12. D

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Hi, everyone here. I have a lot of confusion about the flex cable soldering point during the picofly installation process. I've seen several videos, but I think each individual has a different way of soldering. Solder the third pin in the direction of the triangle sign Someone soldered the 3rd...
  13. D

    Hardware Hacking SXCORE Installation: Using V1 Flex Connector On V2 Switch?

    Don't you put it on the side? When I looked at the cables of Oled and v2 models, I saw soldering both sides of the capacitor.
  14. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Does anyone know of any cpu cables that will be used instead of MOSFET? I saw that the V2 cable is used in OLED and LITE versions. By the way, Mariko used V1 cable. Can't I use V2 cable in mariko? Conversely, is V1 cable not available in OLED and LITE versions? And V3 cable seems to be...
  15. D

    Hacking Hardware I have a question about GND location when installing hwfly.

    Thank you very much for your feedback. I'm planning to connect GND. Short distance, thick cable I take note of it Thank you so much!
See more