Tutorial  Updated

Swap sysnand and emunand (arm9loaderhax only)

Arm9loaderhax coupled with AuReiNand gives us lucky 3DS users the amazing option of running Custom Firmware on sysnand. The advantages of this are as follows:
  • Much faster and more reliable CFW cold booting compared to menuhax + emunand
  • Slightly faster CFW cold booting compared to arm9loaderhax + emunand
  • Using 2GB of SD card space for emunand is no longer needed (but still recommended to keep a 9.2 emunand around)
  • GBA ROMs only need to be installed once, since they run from sysnand now!

Most CFW users will already have a 9.2 sysnand which is usually kept as vanilla as possible, and then an emunand running a higher FW version (i.e. 10.5) booted through CFW. With arm9loaderhax and AuReiNand, we can now swap the firmware versions over so 10.5 runs directly on SysNand, and EmuNand is used only when 9.2 is really needed (e.g. for running decrypt9). This tutorial will walk you through the process of swapping your sysnand and emunand, and changing your arm9loaderhax to use AuReiNand in order to cold boot directly to a patched 10.5 sysnand.

This tutorial assumes the following:
  • You have a 9.2 or below sysnand and CFW running an emunand of a higher firmware version
  • You know how to verify a SysNAND backup using md5
  • You know how to back up your sysnand, emunand and SD card
  • You know how to access hax to get to the Homebrew Launcher
  • You know how to install homebrew apps on your 3DS
  • You know how to install CIAs
  • You have already captured your OTP and built an arm9loaderhax installer
  • You have FBI installed on your sysnand
I won’t explain how to do all of these as this guide is intended to be an overview of the process I used to swap my sysnand and emunand.


If you follow this guide and do not have a valid sysnand backup, you risk bricking your console and this may not be recoverable without a hardmod.

This guide involves updating your sysnand to 10.5. If you don’t have a reliable way of downgrading to 9.2 if you need to, don’t follow this guide. This means you need to be able to use arm9loaderhax to boot CFW, or have a hardmod and a NAND backup, if you want to undo this.

Do not attempt this procedure without a working arm9loaderhax installer. A hardmod is not required but is recommended.


You will need:
  • Homebrew hax already set up and running on your sysnand
  • CFW already installed with a working emunand
  • Decrypt9
  • EmuNAND9
  • MiniPasta
  • AuReiNand mod (do not install this yet)
If you already have arm9loaderhax set up to boot your emunand, you will need to remove it. This is because one of the needed tools, decrypt9, can only run from sysnand. Arm9loaderhax will prevent you from entering sysnand at all, so will need to be removed. I did this by restoring a vanilla 9.2 sysnand backup which I took from the console prior to installing arm9loaderhax.


Stage 0: Make a backup of your SysNand, EmuNand and 3DS SD card

Seriously, you’ll be glad you did if something goes wrong. This process involves a lot of messing around with both sysnand and emunand.


Stage 1: Dump EmuNAND partitions
  1. Boot your 3DS to sysnand
  2. Launch hax and run MiniPasta
  3. When back at sysnand, launch hax and run Decrypt9
  4. Go to “EmuNAND Options” and then “Partition Dump”
  5. Dump each of the partitions with the exception of FIRM0 and FIRM1, pressing B after each one to return to the menu and dump the next partition
  6. Press START to quit Decrypt9, and reboot back to sysnand

Stage 2: Downgrade EmuNand to 9.2
  1. From sysnand, launch hax and run MiniPasta
  2. When back at sysnand, launch hax and run EmuNAND9
  3. Choose “EmuNAND Manager Options” and then choose “Clone SysNAND to EmuNAND”
  4. Once this is complete, press START to reboot
  5. From sysnand, launch hax and run TinyFormat to format SysNand and unlink NANDs
  6. Once the system reboots, complete the initial setup without linking NNID
  7. Once you are at the home menu, set your sysnand theme to red
  8. Launch hax and run CFW to get into emunand
  9. Once in emunand, set the theme to blue
  10. Power off the 3DS

At this point, your sysnand and emunand should both be on 9.2, and you should have dumps of your original emunand. The purpose of setting the NAND colours to red and blue is to ensure you can tell which NAND you are in, since they are both at this stage running the same FW version and will look identical.


Stage 3: Update SysNand to AuReiNand CFW 10.5
  1. Take out your 3DS SD card and put it in your computer
  2. Replace the rei folder, arm9loaderhax.bin and ReiNand.dat in the root of your SD card with the ones from AuReiNand.
  3. In the new rei folder on your SD card, place the firmware.bin and firmware90.bin from the FIRMs archive linked from the AuReiNand GitHib page
  4. Create an empty file on the SD card in the /rei folder called updatedsysnand
  5. Put your SD card back in your 3DS and boot it up to sysnand
  6. Launch hax and run arm9loaderhax.3dsx to install the loader
  7. If you get stuck on a message saying “Exploiting arm9…”, you can safely reboot your 3DS
  8. The 3DS will reboot once this process is complete
  9. You should now be in sysnand but running ReiNand. Verify that arm9loaderhax has been installed by powering off your 3DS, removing the SD card and powering on again. Your system should hang on a black screen because the arm9payload is not available. If your 3DS boots to sysnand without the SD card inserted, this means that arm9loaderhax has not been installed properly and you MUST NOT proceed
  10. Once you have verified that arm9loaderhax is working, replace the SD card and power on your 3DS to boot to sysnand
  11. Open System Settings set up your Internet connection
  12. Update to 10.5 (seriously, don’t do it unless you’re certain the CFW is running by doing the SD card removal test in step 9. If you update to 10.5 without CFW up and running, you risk not being able to run any unsigned code, meaning you could end up stuck on 10.5 with no CFW)
  13. Once the update is complete and the system has rebooted, enter System Settings to verify that you are now on 10.5


Step 4: Reinject emunand partitions to sysnand

This stage will make your new 10.5 sysnand how your emunand used to be
  1. Power off the 3DS
  2. While holding L, power the 3DS back on. This will boot into the 9.2 emunand
  3. Launch hax, and run Decrypt9
  4. Choose “SysNAND Options” and then “Partition Inject”
  5. Inject each of the partitions in turn, with the exception of FIRM0 and FIRM1, pressing B after each one to return to the menu and inject the next partition
  6. Press START to quit Decrypt9 and reboot back to SysNand.

If everything went according to plan, you should be looking at your sysnand but with all your CIAs showing. In my case, they were all back in presents and out of their folders which was a mild inconvenience. I also lost my custom theme, so that had to be reinstalled.


Final checks
  1. Launch a CIA from sysnand to verify that it works. Successful launching of a CIA will indicate that the sysnand CFW is working
  2. Enter System Settings from sysnand to confirm that you are on 10.5
  3. Power off your 3DS, and power it back on while holding L. You should then be booted to your emunand, which will resemble your sysnand before the swap over
  4. Enter System Settings from emunand to confirm that it is on 9.2
  5. Now, do another sysnand, emunand and SD backup!
 
Last edited by mashers,

mashers

Stubborn ape
OP
Member
Joined
Jun 10, 2015
Messages
3,837
Trophies
0
Age
40
Location
Kongo Jungle
XP
5,074
Country
Thanks - good catch!

--------------------- MERGED ---------------------------
Holy fucking shit, I am amazed. :bow:

TBH this is pretty much a writeup of all the help I got in the AuReiNand thread and others from a range of different people. I just pulled it all together and tested it ;)

--------------------- MERGED ---------------------------

Woah, my reply to you somehow appeared above your post :huh:

I hope it's not a side-effect of NAND-swapping...
 

hobbledehoy899

Well-Known Member
Member
Joined
Nov 13, 2015
Messages
2,874
Trophies
1
XP
2,191
Country
Antarctica
Arm9loaderhax coupled with AuReiNand gives us lucky 3DS users the amazing option of running Custom Firmware on sysnand. The advantages of this are as follows:
  • Much faster and more reliable CFW cold booting compared to menuhax + emunand
  • Slightly faster CFW cold booting compared to arm9loaderhax + emunand
  • Using 2GB of SD card space for emunand is no longer needed (but still recommended to keep a 9.2 emunand around)
  • GBA ROMs only need to be installed once, since they run from sysnand now!

Most CFW users will already have a 9.2 sysnand which is usually kept as vanilla as possible, and then an emunand running a higher FW version (i.e. 10.5) booted through CFW. With arm9loaderhax and AuReiNand, we can now swap the firmware versions over so 10.5 runs directly on SysNand, and EmuNand is used only when 9.2 is really needed (e.g. for running decrypt9). This tutorial will walk you through the process of swapping your sysnand and emunand, and changing your arm9loaderhax to use AuReiNand in order to cold boot directly to a patched 10.5 sysnand.

This tutorial assumes the following:
  • You have a 9.2 or below sysnand and CFW running an emunand of a higher firmware version
  • You know how to verify a SysNAND backup using md5
  • You know how to back up your sysnand, emunand and SD card
  • You know how to access hax to get to the Homebrew Launcher
  • You know how to install homebrew apps on your 3DS
  • You know how to install CIAs
  • You have already captured your OTP and built an arm9loaderhax installer
  • You have FBI installed on your sysnand
I won’t explain how to do all of these as this guide is intended to be an overview of the process I used to swap my sysnand and emunand.


If you follow this guide and do not have a valid sysnand backup, you risk bricking your console and this may will not be recoverable without a hardmod.

This guide involves updating your sysnand to 10.5. If you don’t have a reliable way of downgrading to 9.2 if you need to, don’t follow this guide. This means you need to be able to use arm9loaderhax to boot CFW, or have a hardmod and a NAND backup, if you want to undo this.

Do not attempt this procedure without a working arm9loaderhax installer. A hardmod is not required but is recommended.


You will need:
  • Homebrew hax already set up and running on your sysnand
  • CFW already installed with a working emunand
  • Decrypt9
  • EmuNAND9
  • MiniPasta
  • AuReiNand mod (do not install this yet)
If you already have arm9loaderhax set up to boot your emunand, you will need to remove it. This is because one of the needed tools, decrypt9, can only run from sysnand. Arm9loaderhax will prevent you from entering sysnand at all, so will need to be removed. I did this by restoring a vanilla 9.2 sysnand backup which I took from the console prior to installing arm9loaderhax.


Stage 0: Make a backup of your SysNand, EmuNand and 3DS SD card

Seriously, you’ll be glad you did if something goes wrong. This process involves a lot of messing around with both sysnand and emunand.


Stage 1: Dump EmuNAND partitions
  1. Boot your 3DS to sysnand
  2. Launch hax and run MiniPasta
  3. When back at sysnand, launch hax and run Decrypt9
  4. Go to “EmuNAND Options” and then “Partition Dump”
  5. Dump each of the partitions with the exception of FIRM0 and FIRM1, pressing B after each one to return to the menu and dump the next partition
  6. Press START to quit Decrypt9, and reboot back to sysnand

Stage 2: Downgrade EmuNand to 9.2
  1. From sysnand, launch hax and run MiniPasta
  2. When back at sysnand, launch hax and run EmuNAND9
  3. Choose “EmuNAND Manager Options” and then choose “Clone SysNAND to EmuNAND”
  4. Once this is complete, press START to reboot
  5. From sysnand, launch hax and run TinyFormat to format SysNand and unlink NANDs
  6. Once the system reboots, complete the initial setup without linking NNID
  7. Once you are at the home menu, set your sysnand theme to red
  8. Launch hax and run CFW to get into emunand
  9. Once in emunand, set the theme to blue
  10. Power off the 3DS

At this point, your sysnand and emunand should both be on 9.2, and you should have dumps of your original emunand.


Stage 3: Update SysNand to AuReiNand CFW 10.5
  1. Take out your 3DS SD card and put it in your computer
  2. Replace the rei folder, arm9loaderhax.bin and ReiNand.dat in the root of your SD card with the ones from AuReiNand.
  3. In the new rei folder on your SD card, place the firmware.bin and firmware90.bin from the FIRMs archive linked from the AuReiNand GitHib page
  4. Create an empty file on the SD card in the /rei folder called updatedsysnand
  5. Put your SD card back in your 3DS and boot it up to sysnand
  6. Launch hax and run arm9loaderhax.3dsx to install the loader
  7. If you get stuck on a message saying “Exploiting arm9…”, you can safely reboot your 3DS
  8. The 3DS will reboot once this process is complete
  9. You should now be in sysnand but running ReiNand. Verify that arm9loaderhax has been installed by powering off your 3DS, removing the SD card and powering on again. Your system should hang on a black screen because the arm9payload is not available. If your 3DS boots to sysnand without the SD card inserted, this means that arm9loaderhax has not been installed properly and you MUST NOT proceed
  10. Once you have verified that arm9loaderhax is working, replace the SD card and power on your 3DS to boot to sysnand
  11. Open System Settings set up your Internet connection
  12. Update to 10.5 (seriously, don’t do it unless you’re certain the CFW is running by doing the SD card removal test in step 9. If you update to 10.5 without CFW up and running, you risk not being able to run any unsigned code, meaning you could end up stuck on 10.5 with no CFW)
  13. Once the update is complete and the system has rebooted, enter System Settings to verify that you are now on 10.5


Step 4: Reinject emunand partitions to sysnand

This stage will make your new 10.5 sysnand how your emunand used to be
  1. Power off the 3DS
  2. While holding L, power the 3DS back on. This will boot into the 9.2 emunand
  3. Launch hax, and run Decrypt9
  4. Choose “SysNAND Options” and then “Partition Inject”
  5. Inject each of the partitions in turn, with the exception of FIRM0 and FIRM1, pressing B after each one to return to the menu and inject the next partition
  6. Press START to quit Decrypt9 and reboot back to SysNand.

If everything went according to plan, you should be looking at your sysnand but with all your CIAs showing. In my case, they were all back in presents and out of their folders which was a mild inconvenience. I also lost my custom theme, so that had to be reinstalled.


Final checks
  1. Launch a CIA from sysnand to verify that it works. Successful launching of a CIA will indicate that the sysnand CFW is working
  2. Enter System Settings from sysnand to confirm that you are on 10.5
  3. Power off your 3DS, and power it back on while holding L. You should then be booted to your emunand, which will resemble your sysnand before the swap over
  4. Enter System Settings from emunand to confirm that it is on 9.2
  5. Now, do another sysnand, emunand and SD backup!
Holy fucking shit, I am amazed. :bow:
 

Hayleia

Well-Known Member
Member
Joined
Feb 26, 2015
Messages
1,485
Trophies
0
XP
1,294
Country
France
I'm probably too lazy to do this if it's just for GBA games, but that's still great to see well written tutorials like this one :)
 
  • Like
Reactions: Raylight

mashers

Stubborn ape
OP
Member
Joined
Jun 10, 2015
Messages
3,837
Trophies
0
Age
40
Location
Kongo Jungle
XP
5,074
Country
The hax.. it's getting to us man!
They're certainly getting to me... Bed time!

I'm probably too lazy to do this if it's just for GBA games, but that's still great to see well written tutorials like this one :)
It's not just for that. It's also to increase your smugness level. Trust me, it works.

Oh, I added an explanation of why the NAND themes need to be set to red and blue.
 
  • Like
Reactions: Hayleia

hobbledehoy899

Well-Known Member
Member
Joined
Nov 13, 2015
Messages
2,874
Trophies
1
XP
2,191
Country
Antarctica
TBH this is pretty much a writeup of all the help I got in the AuReiNand thread and others from a range of different people. I just pulled it all together and tested it ;)
Still, this is amazing and you're the one who proved it.

Woah, my reply to you somehow appeared above your post :huh:

I hope it's not a side-effect of NAND-swapping...
It's a limitation of GBAtemp.
 

Hayleia

Well-Known Member
Member
Joined
Feb 26, 2015
Messages
1,485
Trophies
0
XP
1,294
Country
France
It's not just for that. It's also to increase your smugness level. Trust me, it works.
Lol :P
Well, after doing MSET→menuhax then menuhax→arm9loaderhax, I really don't need another dose of smugness I think :P

Another reason (a bit more serious) is that I don't have a hardmod, so just in case I do stupid things to my main NAND, I'd rather it be the emu one ;)
And whenever I need to boot a GBA game, I can just boot AuReiNAND (why not "ReiNAND done Wright" :P) with A held down.
 

mashers

Stubborn ape
OP
Member
Joined
Jun 10, 2015
Messages
3,837
Trophies
0
Age
40
Location
Kongo Jungle
XP
5,074
Country
Lol :P
Well, after doing MSET→menuhax then menuhax→arm9loaderhax, I really don't need another dose of smugness I think :P

Another reason (a bit more serious) is that I don't have a hardmod, so just in case I do stupid things to my main NAND, I'd rather it be the emu one ;)
And whenever I need to boot a GBA game, I can just boot AuReiNAND (why not "ReiNAND done Wright" :P) with A held down.
Yeah, this is risky without a hardmod as you are updating sysnand to 10.5. If something goes wrong with your arm9loaderhax, you're basically fucked.
 

Site & Scene News

Popular threads in this forum

General chit-chat
Help Users
  • K3Nv2 @ K3Nv2:
    Bigonya uses his wiener to mod 360s
    +1
  • Xdqwerty @ Xdqwerty:
    Going to the water park, see ya
  • BigOnYa @ BigOnYa:
    You should update the 360 to newest dash before RGHing it yes. But not a big deal if you don't, you can install new dash/avatar updates after. It's just easier to do it auto online before, instead manual offline after.
  • BigOnYa @ BigOnYa:
    Have fun @Xdqwerty. If you see a chocolate candy bar floating in the water, don't eat it!
  • AncientBoi @ AncientBoi:
    :O:ohnoes: Y didn't U Tell ME that ALSO? @BigOnYa :ohnoes: 🤢🤮
    +1
  • BigOnYa @ BigOnYa:
    Does it taste like... chicken?
    +1
  • S @ salazarcosplay:
    @BigOnYa I wanted to ask you about your experience with seeing south park. Most of the people a bit younger like my younger brother and cousins that are a few younger than me that saw kids found south park funny because of the curse words, kids at school, that seemed like liking the show on a very basic level.

    I could not quite have a in depth discussion of the show.

    How was it for you? As an adult. What did you find the most interesting part about it. Did you relate to the parents of the kids and their situations. Was it satires, the commentary on society. The references on celebrities' and pop culture.
    +1
  • BigOnYa @ BigOnYa:
    I remember seeing the very first episode back in the day, and have watched every episode since. I used to set my VCR to record them even, shows how long ago.
  • BigOnYa @ BigOnYa:
    I just like any comedies really, and cartoons have always been a favorite of mine. Family guy, American Dad, Futurama, Cleveland Show, Simpsons - I like them all.
    +1
  • BigOnYa @ BigOnYa:
    South Park is great cause they always touch on relavent issues going on today, and make something funny out of it.
    +3
  • S @ salazarcosplay:
    @BigOnYa were you always up to date on the current events and issues of the time or were there issues that you first found out thru south park
  • BigOnYa @ BigOnYa:
    Most of the time yea I knew, I watch and read the news regularly, but sometimes the Hollywood BS stuff, like concerning actors slip by me. I don't follow most Hollywood BS (example: the Kardasians)
    +2
  • S @ salazarcosplay:
    @BigOnYa there were relevant issues before south park was made, that's why i think a south park prequel/spinoff would be great. Randy and his friends in their child hood
    +1
  • BigOnYa @ BigOnYa:
    Yea, like them running in high school together, getting into stuff, and how they got hitched and had kids. And how the town of South Park was back then compared to now. That would be cool to see.
  • BakerMan @ BakerMan:
    yeah
  • The Real Jdbye @ The Real Jdbye:
    @salazarcosplay if they made a prequel, it would still be about current issues, cause it doesn't make sense to make it about stuff that happened 30 years ago that nobody cares about anymore
  • The Real Jdbye @ The Real Jdbye:
    it's too late
  • The Real Jdbye @ The Real Jdbye:
    the older south park episodes about particular issues usually age poorly since the topic is no longer relevant
  • The Real Jdbye @ The Real Jdbye:
    an exception is giant douche vs turd sandwich, that's always relevant :P
    +1
  • K3Nv2 @ K3Nv2:
    I was gone for like an hour and none of you thought to write or call pos
  • BigOnYa @ BigOnYa:
    We knew you were going to Sonic to get lunch.
  • K3Nv2 @ K3Nv2:
    Sonics fast I would've been home in 10 mins
  • BigOnYa @ BigOnYa:
    Meet and greet with AncientBoi then?
  • K3Nv2 @ K3Nv2:
    That would've gone slow he's old
    +1
    K3Nv2 @ K3Nv2: That would've gone slow he's old +1