Search results

  1. K

    Switch OLED teardown V1/V2

    De9ed did my Oled for me. Very fast, great communication, and reasonable prices. If you see some of my earlier posts, you will notice I tried to do an HWFLY lite in Oled (before the new Oled specific version) and botched it pretty bad. De9ed helped me out and I have a wonderful Oled with Oled...
  2. K

    Hardware Hacking HWFLY LED Test

    It was from Ming, Hwfly Lite v3 Oled cable bundle
  3. K

    Switch OLED teardown V1/V2

    Yea I tried the solder mask and it would melt when iron got close. I removed the chip and install board back in case and nothing comes on, no screen, no fan, cpu doesn’t heat up. I tried with battery and charging cable. I plan to buy a new one and new chip and have a different installer do it.
  4. K

    Switch OLED teardown V1/V2

    If anyone needs a Switch OLED donor board DM me. I also have an HWFLY Lite as well. Probably need another cable set for it though.
  5. K

    Switch OLED teardown V1/V2

    Yea, so if that's the case what can I do? Just buy a new one?
  6. K

    Switch OLED teardown V1/V2

    So I think my issue was with the CLK point. It keeps beeping with multimeter so I think it’s grounded or a short. The problem is this copper stuff around the point where I scratched the CLK, the solder wants to stick to that and it’s grounded. Did I scratch too deep or not enough?
  7. K

    Switch OLED teardown V1/V2

    I doubt it, I can connect via USB and it seems to be doing what its supposed to be doing. I probably just messed up the soldering and fried the board. I will probably just try to sell it as a donor board
  8. K

    Switch OLED teardown V1/V2

    So with red on ground and black on the points I get: DAT0 - 494 CLK- 493 CMD- 416 RST- 458
  9. K

    Switch OLED teardown V1/V2

    Never got green, only glitching (flashing blue, then solid red or white). All the reading seem right, no shorts. Everyone says it’s DAT0, but I tested several times, even removed and replaced the adapter and I get ~800 in diode mode every time, on the adapter and on the modchip side as well...
  10. K

    Switch OLED teardown V1/V2

    I was doing red on points, black on ground, but it should read the same way I believe
  11. K

    Switch OLED teardown V1/V2

    Looks like its just dead. I tried replacing the DAT0 adapter, and doing USB debugging, but I keep getting BAD0010D. I installed the board back in the switch and I get no screen or fan when powering on.
  12. K

    Switch OLED teardown V1/V2

    Were you replying to me? If so, all the videos I see and other posts say it should reading around 2.9 in diode mode and I get nothing, nothing on chip and nothing on motherboard. Here are my readings if anyone can point me in the right direction, or if I should just trash it and start over...
  13. K

    Switch OLED teardown V1/V2

    Thank you. That’s one problem fixed. Now does anyone know why the RST point on the motherboard doesn’t give any diode reading? It’s just a solder point, so no resistor or capacitor could have burnt off, but I am not getting any reading, even after removing the chip connection
  14. K

    Hardware Hacking HWFLY LED Test

    So I received the board back and tested the connections. All connections including DAT0 (~750-850) seem to be within correct ranges. However I am getting no reading (1 on my multimeter) for the RST connection. The thing that worries me is I don’t get a reading from the motherboard even after...
  15. K

    Switch OLED teardown V1/V2

    Can anyone help me with this? I was plugging this back in and it was apparently upside down, the tweezers slipped and I pulled the black cable from the connector. Is there an easy way to repair, or do I need to purchase a new 2-pin JST connector (if anyone knows the size that would help) and...
  16. K

    Tutorial OLED HWFLY Success! Be careful with that LCD Connector, How I replaced mine.

    Where are the connections located for the O1V2-8 connectors? Looks like it’s for the CMD, CLK, 3.3v and GND given the shape, but since the CPU cable is straight, I can’t figure out how all this would line up and plug in to the chip. Also can this one be flashed?
  17. K

    Switch OLED teardown V1/V2

    That’s what I am thinking, the Hwfly should fail if no dat0 emmc data, and I don’t think the emmc would boot if the switch is off in charging mode. Otherwise the chip would be on all the time
  18. K

    Hardware Hacking HWFLY LED Test

    Has anyone tested an HWFLY Lite on OLED before installing in case? I have a professional installer doing all the micro-soldering for me. All the connections look good, however I only sent the motherboard and chip (plus chip accessories), no case or screen or battery. When they plug in a USB-C...
  19. K

    Switch OLED teardown V1/V2

    There is no screen or SD card slot attached. Just the motherboard with usb-c power cable.
  20. K

    Switch OLED teardown V1/V2

    So the light on the chip should go green even if the board isn’t installed in the case? My theory is that since the switch wasn’t “booting”, just charging that the chip tries to boot hence the blue/purple light, then red because nothing to attack, then off since the switch is just charging. I...