Search results

  1. vastrolorde

    Switch OLED missing the CMD capacitor

    can you point out where in the 3ds motherboard can you get this resistor. thanks in advance. internet say this is a 0201 4.7k resistor
  2. vastrolorde

    Hardware Nintendo switch lite lost resistors value

    hi if you dont mind checking capacitor specs on my switch lite board too? no spare board to test. so would really appreciate if you coud look into this? https://ibb.co/zGPtbyQ
  3. vastrolorde

    Hardware switch lite capacitor values

    just bought a defective switch lite, with a lot of missing capacitors.. anyone expert or has a spare unit know the values and sizes of the caps highlighted on the picture? and if also i can get those caps from a donor switch v1 board? i have one here broken into two pieces. TIA...
  4. vastrolorde

    Hardware M92T36 or BQ24193

    One of my switch unit is unable to charge the battery, Unit is working normally, plugging the original wall charger, gives it a charging icon. but battery percentage drops. so it detects that the charger is plugged in, but no voltage going to the battery. Tests Done. Rev HAC CPU21 tried...
  5. vastrolorde

    Hardware switch v2 water damaged repair

    already tried using official switch charger and tru power bank... already a tested charged battery, still not powering on.
  6. vastrolorde

    Hardware switch v2 water damaged repair

    not reading any voltage on each side of the fuse, when plugged in.. wondering if this is caused by the max ic underneath battery connector? read somewhere here bout that, poviding the power to the rail, but i dont know how test it if its defective.
  7. vastrolorde

    Hardware switch v2 water damaged repair

    I'm getting continuity on the fuse, so i assume its good, not getting 3v on m92. no shorts around m92, BQ, P13 cleaned the board thoroughly just right after it was accidentally dropped. what component should i check? responsible for sending voltage to M92 chip?
  8. vastrolorde

    Hardware switch v2 water damaged repair

    working on a v2 water damaged unit, after cleaning the board. and installed new M9 IC, assembled and tested it with a good charged battery, but unfortunately im still not getting any reading on M92T36, no 3v on pin 5/6, no 1.8v, getting around 3.9v on caps around BQ IC near the battery. any...
  9. vastrolorde

    Hardware Sx core defective?

    I've already installed quiet few sx core/lite modchips my own, but im having issue with 2 sx core modchips.. that a friend of mine bought from a local reseller.. its blinking blue at first, then after a while a solid red light. i can confirm that the ribbon is soldered correctly on the APU...
  10. vastrolorde

    Hardware Switch V2 no power, Apu heating quickly

    Need your advice, switch not powering on. Now APU Heating rapidly after removing sx core ribbon with battery connected and pressing the power buttonmakes the APU heatup so fast. tested components using multimeter around M9, BQ, P13 no shorted capacitors.. Sx core installed.blinking blue...
  11. vastrolorde

    Hardware Switch Lite resistor value..

    Good day!.I happen to lost a resistor just above the fpc connector on a nintendo switch lite.. anyone has a spare switch lite yo test? i have a spare switch version 1 scrap motherboard. Thanks in adance..
  12. vastrolorde

    Hardware switch v2 capacitor value

    thanks a lot mate, need to check if can find one on a scrap version 1 board.
  13. vastrolorde

    Hardware switch v2 capacitor value

    Good day!:):) does anyone know the exact value of this two caps. in which we solder the sxcore ribbon cable.. i need to get replacement.. since i accidentally removed and lost it. TIA https://imgur.com/eMaTAbw
  14. vastrolorde

    Hardware BSOD need expert advice.

    Switch Original Issue: No display on dock mode but working on handheld. charges ok. so type c port is ok decided to put a bnew p13usb chip. after replacement. dock issue still persist. green light on dock but no display on lcd. tried another known good working switch tablet, display ok on lcd...
  15. vastrolorde

    Where to buy SX core?

    would really appreciate if you can send me too..
  16. vastrolorde

    Hardware Switch hard mod NAND dump, with Low Voltage eMMC Adapter.

    actually my switch,s problems is kinda weird, its not Bluescreen, but shorted caps, when emmc module is connected on the board, all shorts gone, after removing it. so maybe, i just thought that this method might work. so i can replace it with a good working emmc module.
  17. vastrolorde

    Hardware Switch hard mod NAND dump, with Low Voltage eMMC Adapter.

    Can this be done using a regular Micro sd adapter? just like what we used back then on the 3ds, to dump the NAND?
  18. vastrolorde

    Hardware Fixing a water damaged switch. No video on LCD, but video in dock mode on TV.

    wha did you manage to fix this?? cause im actually having the same issue, mines just a little bit different.. im not getting any display on lcd. just backlight. but i can hear the sound that the unit is working and booting up and touch screen is also working when im testing it. displays works...
  19. vastrolorde

    Hardware HELP, Nintendo switch board, is this repairable?

    i'm really having a nightmare:cry::cry:, to found out one of my unpatched unit motherboard was broken into two. so i badly need expert advice, if this case is even repairable?? dont know if i can solder the traces on both sides of the board, and maybe use jumper wires to connect some. would that...
  20. vastrolorde

    ROM Hack RELEASE Bloodstained: Ritual of the Night 60 FPS mod

    i Dont know if this is the right thread to request, but it would be awesome if we can get a fps patch on friday the 13th game. i mean the fps sucks. i think this game runs on unreal engine as well. TIA
General chit-chat
Help Users
    realtimesave @ realtimesave: @DinohScene hi