Search results

  1. R0nny01

    Switch Lite bricked. AutoRCM enabled?!

    Pads looks fine to me. Resistor is also okay and have contact to pads. Exept the cpu flex all cables are removed. Pads looks fine to me. Need a new battery for my multimeter -.- just died. Switch still in APX Mode. EDIT: I replaced the emmc, still same error. APX Mode still there. Found some...
  2. R0nny01

    Switch Lite bricked. AutoRCM enabled?!

    Here are the pictures u asked for. Im sure that autorcm is enabled because the switch is in APX Mode if i connect it to my pc.
  3. R0nny01

    Can I update to 17.0.0 on unmodded Switch before installing HWFLY RP2040?

    You can always update OFW and install picofly afterwards. If the latest fw is not supported, you can create an emummc and downgrade your firmware on emuemmc to a fw that supports latest atmosphere. Correct me if im wrong.
  4. R0nny01

    Switch Lite bricked. AutoRCM enabled?!

    Hello all. I recently bought a bricked switch lite to see if i can fix it. The pre-owner of the switch said that the autorcm bit was set. picofly was removed by pre-owner and i installed picofly back into it to see if i can boot hekate. Picofly tries to glitch (Blue LED), after that i get this...
  5. R0nny01

    Switch Oled emmc replaced

    My Goal here is to get the oled at least run cfw. i got a backup from donor with raw dump and keys. Current status: Emmc replaced Boot0 and Boot1 generated with emmchaccgen flashed to emmc Obtained prod.keys from dead switch Im currently following this guide here: Nand Rebuilding im still...
  6. R0nny01

    Switch Oled emmc replaced

    as mentioned i soldered the new emmc with fresh boot0 and boot1 back to switch. after that i managed to push the lockpick_rcm payload to get the prod.keys file. So in theroy i could boot into hekate and write to the emmc. Picofly wouldnt work if emmc is not correctly installed i assume. 1701901561
  7. R0nny01

    Switch Oled emmc replaced

    Yeah, i know i need an emmc programmer for my later projects, but is an emmc programmer necessary if im able to write to the emmc with hekate? I dont think so, correct me if im wrong. Saved a screenshot of lockpick_rcm.
  8. R0nny01

    Switch Oled emmc replaced

    I now got the prod.keys from my dead switch. stupid me that i broke screen connector -.- So now i need to rebuild nand with my just obtained keys and flash it back to emmc, right?
  9. R0nny01

    Switch Oled emmc replaced

    Okay, I understand. I can at least try to dump the prod.keys from it by pushing lockpick_rcm and simultaneously do the same thing on my v1. If done right I should get the keys, right? At the same time I would see if the switch could launch a payload or not.
  10. R0nny01

    Switch Oled emmc replaced

    Okay, i soldered the emmc back to mainboard. Boot0 and Boot1 flashed with success. Picofly seems to glitch with success. Current draw looks good too. Next step is to wait for new screen connector, because i broke mine. Is there a way to atleast check if the switch actually boots into hekate...
  11. R0nny01

    Switch Oled emmc replaced

    I soldered Dat0, CMD, CLK, VCC, VCCQ and GND. The blank emmc on v1 board showed up in hekate. The generated Boot0 and Boot1 are smaller then original boot files. Is that normal?
  12. R0nny01

    Switch Oled emmc replaced

    I do have boot0, boot1 and prod.keys from an other oled switch. Managed to get the files from a friend. Does this work? I don't care about OFW or eshop kind of things. If I can't flash the files with the rp2040, I could maybe try to wire up the emmc to the v1 switch to flash the files over...
  13. R0nny01

    Switch Oled emmc replaced

    I assume that there is no boot0 and boot1 because it's a new empty emmc. I do have the old emmc but I'm unable to get content out of it. I soldered the old emmc to an emmc board from a v1 switch to try to dump the old emmc with unpachted switch. Unfortunately the emmc is dead. Is it possible to...
  14. R0nny01

    Switch Oled emmc replaced

    Hello all. I do have a switch oled with a new blank emmc. switch wont boot because boot0 and boot1 are missing and because its empty.. i do not have a backup from the old emmc. I do have BOOT0 and BOOT1 from other Switch. is there a way to write these files to the emmc with the...
  15. R0nny01

    Missing Components on OLED near pi3usb ic

    okay, i removed the pi3usb ic and the short is still there. Gonna try to remove the M92T36 and check if the short is gone. EDIT: Short is still there. M92T36 removed and pi3usb removed. Any other suggestions? EDIT2: Found the short. It was the cap of the M92T36....
  16. R0nny01

    Missing Components on OLED near pi3usb ic

    Okay, thank you. i will order them right away. I noticed the 3,3v rail is shorted too, but im unable to find the shorted component. Everything else looks fine too me. What can cause the 3,3v line short? removed some caps on the 3,3v rail, but so far the short is still there.
  17. R0nny01

    Missing Components on OLED near pi3usb ic

    Hello folks, I recently bought a switch oled pcb with missing components near pi3usb ic. Does somebody know the values of the missing components? Thanks :)
  18. R0nny01

    Hardware Wii U weird Video output. vWii working fine. HDMI not working

    Wii U is working fine now. Changed the TV Output to HDMI and its working. lul. The previous owner didnt know about this setting xD Well, got a Wii U for nothing. Now im updating to 5.5.2 and try to use the Webkit exploit. Good Tutorials out here for the Webkit exploit?
  19. R0nny01

    Hardware Wii U weird Video output. vWii working fine. HDMI not working

    Need to get a Gamepad xD im trying with drc-sim to emulate a gamepad ^^ maybe i will get a pad tomorrow. I it possible that this could happen if a update goes wrong?
  20. R0nny01

    Hardware Wii U weird Video output. vWii working fine. HDMI not working

    Hello Community :) I recently got a broken Wii U. vWii is working just fine. No graphic bug or something. HDMI is not working at all. The Wii U part is like zommed in and i can only see a part of the screen. Is there any fix for that? Or is the Wii U Graphics chip broken?
General chit-chat
Help Users
    SylverReZ @ SylverReZ: @The Real Jdbye, :creep: +1