Recent content by superfiege

  1. superfiege

    Hacking Hardware Picofly - a HWFLY switch modchip

    hey there. cool! I will give it a try when I have time. cheers!
  2. superfiege

    Hacking Hardware Picofly - a HWFLY switch modchip

    I was thinking about using a gnd-pin instead of reset, but I dont know if it will create other issues if not all gnd pins of the joycon are real gnd pins and so connected to gnd....
  3. superfiege

    Hacking Hardware Picofly - a HWFLY switch modchip

    so cool! I love the status LED in the lite!!! working perfect. The LED in the light-sensor is also cool, but not a big advantage over the led shining through the ventilation slot. I prefer the led in the joycon, even with some connection problems :) Thank you so much for these cool ideas.
  4. superfiege

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hey there. Nice repair and very nice idea with the location of the stsatus LED!!! I installed one in the right joycon, but the problem with this is, that you get some connection problems sometimes... Is thr single rear mosfet installation working properly? I thout about it but i read that you...
  5. superfiege

    Picofly OLED Error *== or *=*

    I have had this problem several times on perfectly soldered oleds. With flex cables and with wires. Reworked all solder-points. Nothing fixed the problem. It only happens about 1 out of 10 glitching tries. Searching for solutions I figured out the only way (for me) is to replace the picofly...
  6. superfiege

    Hacking Hardware Which picofly setup do you use?

    Are there still people looking for modded switches? In switzerland the demand is very low at the moment.
  7. superfiege

    Hacking Hardware Which picofly setup do you use?

    Hey beloved modders around the world :) Im very interested in which picofly you use for your installations and if you use these flex-cables or pure wires and how you setup your mosfets on the apu. Excited hearing/reading from you!!!
  8. superfiege

    Hardware Switch OLED Instinct-NX V6S blinking green after booting to CFW

    Looks like it was a faulty instinct-chip. switched to picofly, everything workt perfect now.
  9. superfiege

    Hardware Switch OLED Instinct-NX V6S blinking green after booting to CFW

    Ah ok. And then it stays blinking all time? In my case it only stops when i shutdown the switch…
  10. superfiege

    Hardware Switch OLED Instinct-NX V6S blinking green after booting to CFW

    Hi there I recognized, that my Switch OLED with an installed Instinct-NX V6S is sometimes blinking green after glitching sucessfully. It behaves like i would press vol+ during startup to enter instict-toolbox. Anybody else had this issue?
  11. superfiege

    Hacking Hardware Random Short Long Long (*==) on Picofly OLED

    Hi there Did you ever had the problem after modding your switch OLED with a Picofly that randomly you get the error code *== In PicoflyGuide you find *== : No eMMC CMD1 request (poor wiring, or dead CPU) But Im a bit confused, it only happens sometimes. I double checked my wirings and...
  12. superfiege

    Review Sthetix fusecheck: how did this tool get released?

    Hi there Did you update FW using Daybreak and having a Picofly installed? If yes, open your console, disconnect Picofly and boot your switch. then shutdown and reinstall Picofly. This shoud correct your fuse-count. More information and detailed description can be found here...
  13. superfiege

    Hardware Switch Lite USBC connector replacement went kind of wrong

    Hey thank you for your reply. I figured it out. The problem is the connector. If the plug is not alligned perfectly I get these OL-readings. I think its poor quality.
  14. superfiege

    Hardware Switch Lite USBC connector replacement went kind of wrong

    Hi there I tried to replace the usbc connector of an old switch lite. Im not so good in hot air soldering and so i think i damaged something on the board. D+, D- and CC lines are OL now Maybe somebody had the same issue and knows what component I could have broken?
  15. superfiege

    Homebrew Switch OLED pink screen (failed kamikaze)

    Nah, if you damaged dat0 connection you can bridge it to the other side od the pcb. Just kamikaze on the other side and then bridge it. But I think its not a problem with dat0, otherwise the switch wouldnt even start.
See more