Recent content by NizNoz

  1. NizNoz

    Hardware Stock Lite only charging to 35%

    This is awesome! Thanks!! I’ll focus on this area..
  2. NizNoz

    Hardware Stock Lite only charging to 35%

    I think it literally is being charged to 35%. The battery charge seems to be working ok..
  3. NizNoz

    Hardware Stock Lite only charging to 35%

    Bought as "for parts". Seller said it would work while plugged in, and had replaced battery with non-OEM battery. When I recieved, it didn't boot beyond the first logo and the black charging screen. I opened and there was a small amount of what looked like water damage around the back side of...
  4. NizNoz

    Hacking Hardware Picofly - a HWFLY switch modchip

    Fixed! Thanks for the help! It was indeed point B, but because I seated the chip slight in the way of the heat shield. Worth checking if anyone has a similar issue.. as you can see, B runs right next to the shield in my setup. I rerouted it, and shifted the chip a millimeter away.
  5. NizNoz

    Hacking Hardware Picofly - a HWFLY switch modchip

    New clone hwfly install on OLED. Is this amber or yellow.. and what does it mean?? I had checked just before installing metal back cover, and received the “no SD card message”. I turned the console off, inserted the SD card, and continued closing up. Now there’s nothing on the screen, and this...
  6. NizNoz

    Troubleshooting a non-functioning Digitizer

    Oh.. thanks for clarifying @Illuminaticy. I thought that area had to do with audio processing. Here are better pic. The original pic was just to show what components were replaced.
  7. NizNoz

    Troubleshooting a non-functioning Digitizer

    I’ve looked and looked, but can’t see anything that might be shorting. Is this the region of the board you mean?
  8. NizNoz

    Troubleshooting a non-functioning Digitizer

    So I have a new, functioning digitizer/LCD in my lite. I bought the switch as a “damaged unit”, and it had a cracked screen and casing. I think it was thrown or sat on. Anyhoo.. I’ve had to replace an İÇ, a few caps, and an inductor coil (red circle in pic) and it’s finally up and running. But...
  9. NizNoz

    Hardware Can Anyone help identify these Lite components?

    So after installing the components, the console booted!! Yay! (Thanks so much again @jkyoho). However.. digitizer does nothing. I’ve seated and unseated the ribbon, scrubbed the board with IPA. Nothing. I used a known working board and the digitizer works normally. Any ideas? Do the parts I...
  10. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Thanks! For a noob, that wasn't obvious to me. I chose a 1.2A rated one instead.
  11. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Having read and reread around "constant draw".. would something like this work? https://www.digikey.ca/en/products/detail/delta-electronics-cyntec/HTEH20161T-1R0MSR/9761414
  12. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Hi. I've finally returned to my project and am sourcing all the caps and inductor. I'm doing this by going to DigiKey and searcing for the capacitance and lenght/width for caps, but how do I find the appropriate coil? I've done a search for a 1microH inductor, but the item that comes up looks...
  13. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Ok. That makes more sense to me. Thanks for patiently answering all my noob questions 😊 1713202238 For the IC.. this is what I was left with after desoldering the old chip. ie two pads connected. The PDF pin configuration diagram shows that B1 & B2 (LX1 & LX2) are connected together. Am I...
  14. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Thanks! Now I need to just figure out how to read this.. 1713201104 Thanks for your answers! I appreciate it very much! Two follow up questions: So when I powered up, the coil “A” started smoking. I had not placed a capacitor for “B”. Does this outcome make sense? Are the last two capacitors...
  15. NizNoz

    Hardware Can Anyone help identify these Lite components?

    Messed up a repair and fried "A". Sneezed while handling "B" and it disappeared into the 6th dimension. "C" might not be lying flat after re-soldering. Can anyone help me identify them, or point me in the the right direction so I can do so myself? Also, which of these would likely to have...
See more