Recent content by neo1607

  1. N

    Hardware Xbox One (original) Won't power on?

    I have a xbox one, original that will not power on, the power brick stays orange, I have tried several power supplys, also tried a couple of different touch ribbons, I have even tried shorting the power pin direct to ground on the front power board but still nothing. Does anyone have any idea...
  2. N

    Hardware No HDMI and USB not recognised in RCM

    Got a switch that I bought as faulty, would not power on however showed 0.2A on the amp meter. I reflowed M92T36 and BQ24913 and i got it charging properly, still no picture on the screen though. I tested the HDMI filters beside P13USB and found one of them to be faulty so I decided might as...
  3. N

    GCN Suggestion of mods for gamecube?

    Finally getting round to modding these gamecubes, ordered a couple of Xeno chips, I've got plastic primer and paint to freshen up the shells. I was planning on doing the LED controller port mod, can't seem to find a definitive guide on it, is it just standard 3mm 5v leds i use? Some threads...
  4. N

    GCN Suggestion of mods for gamecube?

    And am I right in thinking Xeno GC is just a drive chip to allow backup DVD+R? Whereas likes of GCLoader allows backups from a SD card? Gonna be replacing the laser in one of them anyway as it is struggling with some discs
  5. N

    PS1/2 Best place to buy replacement shells?

    Does anyone know a reliable source for purchasing replacement/custom shells for the original PS2? Got one at a boot sale at the weekend for dirt cheap however the casing is slightly cracked and missing screws, was looking to refurbish it but I only seem to be able to find used shells on eBay...
  6. N

    GCN Suggestion of mods for gamecube?

    I've got 2 Gamecubes sitting here that I fancy using as projects. Can anyone suggest any modifications I could do to them to make them a bit more unique than a bog standard gamecube? I was thinking of paint jobs, and was looking at possible modchips but I have seen that many such as Xeno, Wasp...
  7. N

    Hardware Switch with no display

    Nothing as well, i don't think i've put this m92t36 on properly lol, although why am i getting RCM and backlight
  8. N

    Hardware Switch with no display

    Don't get anything on them
  9. N

    Hardware Switch with no display

    yeah that's with charger plugged in, pin 5 gets 6v, pin 6 gets 3.3v but those pins you said only get around 1.2mv?
  10. N

    Hardware Switch with no display

    Roughly 1.2mv on all those pins, so next to nothing, I maybe need to try reflowing M92T36
  11. N

    Hardware Switch with no display

    It's weird, it has a usb connection, but it's not drawing any amps, TegraRCM detects it fine and I can inject payloads fine
  12. N

    Hardware Switch with no display

    Yeah it's unpatched.
  13. N

    Hardware Switch with no display

    Bought a second hand switch off ebay, it was classed as "dead". No amp draw using an amp meter, and no usb detected. I replaced M92T36 and I now get 6v on pin 5 and I get 3v on pin 6 when I press power, I also get RCM so i'm assuming it's had autoRCM installed at some point. If I try to boot...
  14. N

    Hardware 2162-0002 Error, is it fixable?

    Anyone got any ideas before it goes on eBay for spares and repairs?
  15. N

    Hardware 2162-0002 Error, is it fixable?

    Small note: managed to just get past the inital launch screen, it was crashing with the error every single time the keyboard popped up for input entry, however i removed the joycons and turned them off so the switch was in tablet only mode and I have now managed to get to the home screen Update...
See more