Recent content by mahdi2023

  1. mahdi2023

    can same one help me with those ripped speaker pads

    very helpfull thank you
  2. mahdi2023

    can same one help me with those ripped speaker pads

    thank for your reply i have scratch those two pad but when i mesure with continuous multemeter they are link to ground those two pad it is normal ?
  3. mahdi2023

    can same one help me with those ripped speaker pads

    can same one help me with those ripped speaker pads i have try to scratch those two ripped pads but as the pcb is multi layer i have found that under those there ripped pads is GND any solution how can i jump the two cable of speaker to other place
  4. mahdi2023

    please what is the value of those resitor ?

    hi when i buy this switch v2 i have found that was missing those two resistor i don't have the an old resistor to read it 1761857058 can samone here mesure me the value from his NS
  5. mahdi2023

    please what is the value of those resitor ?

    please what is the value of those resitor ? i have replace with 4.7k it is correct ?
  6. mahdi2023

    Question about flex cable v2

    Hi dear i have a second ns mariko v2 xkj i have buy the new core v5 from hwfly on alixpress and i'am wating the parc soon. My twi question i have othe cable v2 new the time i receive the parcel. Can i solder it on switch and add same plastic rubbon to pin flex cable ? What happen to nintendo...
  7. mahdi2023

    Picofly ripped pad ?

    i have flash it with fw_2.67.uf2
  8. mahdi2023

    Picofly ripped pad ?

    t thank u , i have flash good the rp2040 before i start remove the button and usb but i think those button have no use after we flash , i'am asking here my question because i afraid any wrong thing can damage my nand at the end thank u again
  9. mahdi2023

    Picofly ripped pad ?

    Hi team i have start flashing the rp2040 zero and the flash was ok done with red light. Then when i have remove the reset button i see they are a ripped pad on reset pcb ? Does i need continu or not ? Thank u
  10. mahdi2023

    please i need the picofly schematic for v2 mariko

    WITH PICOFLY YES BUT I HAVE MADE other installation before with hwfly.
  11. mahdi2023

    please i need the picofly schematic for v2 mariko

    Is there a document or a link to measure my installation and check before powering up. as a precaution, that is to say what value I must have exactly to avoid the short circuit and the death of NAND. and big thank again for your help
  12. mahdi2023

    please i need the picofly schematic for v2 mariko

    thank u
  13. mahdi2023

    please i need the picofly schematic for v2 mariko

    thank u for your answer i have same question please : 1 : ON THE FLEX cable there are 6 pin do i need solder pin 3 and 4 together to the cpu rp2040 ? 2 : do i need solder the v2 flex cable like normal solder same as hwfly on APU ? 3 : do i need solder the DAT 0 on mother bord on the the...
  14. mahdi2023

    please i need the picofly schematic for v2 mariko

    hi please i need to correct picofly schematic rp2040 zero for v2 mariko with flex cable v2 do avoid any damage for the switch thank u
  15. mahdi2023

    pleae help with hwfly Support V1 V2, Erista Mariko, Core V5

    this one https://www.aliexpress.com/item/1005003931472903.html?spm=a2g0o.order_list.order_list_main.51.3dfc1802dM0y3d but it's a trash .
See more