Recent content by M-O-B

  1. M-O-B

    Tutorial Trinket Internal Install.

    so basically the data pads have been damaged, if I get chance I'll test if the 2 pads go to anywhere else, looking at the image it looks like they end at the pads. if you have a old USB lead you can cut the USB A plug off and test the green and white wires, to see if your getting a connection...
  2. M-O-B

    Tutorial Trinket Internal Install.

    OP updated with uf2 drag and drop files for dongles or for a 4 wire internal install.
  3. M-O-B

    Hacking switch issue

    ok guys got a switch and it's stuck on this screen, can't get past it because the right joycon connector on mobo is missing.. this whole connector is gone, only thing left are the pads. I'm hoping that someone can help me out with the actual pinout for the mobo pads so I can do a hard wire...
  4. M-O-B

    Hardware sd card port issue

    decided not to use the original sd card module, as I didn't trust it, so tomorrow I'll be trying this out as an alternative fix for the module, or at least till I find a better solution. but will be looking at getting something like this for a better solution..
  5. M-O-B

    Tutorial Trinket Internal Install.

    I will be posting new updated at some point in next 24 hours. I wouldn't play online if you mod your console. as for install diagram I don't use any that I posted now. I only install using 4 wires & a 10k resistor. power. gnd. data+ data- 10k resistor between pin 7 & 10 in right joycon, or...
  6. M-O-B

    Hardware sd card port issue

    sd card module image 1 updated in the OP with white and orange pins in correct place.. if anyone has the pinout for the right joycon mobo pins, I'd be grateful if you could post it. I only know pin 10, I'm really only after pin 7 for the right joycon, as I use pin 7 & 10 instead of a jig.
  7. M-O-B

    Hardware sd card port issue

    I tested the pins on the port on mobo, and these are the required pads. mine was the green pin that was missing along with the GND pin next to it. I managed to get the console to load the sxos but it still didn't find the sd card on the console. so at least I was able to delete emunand so...
  8. M-O-B

    Hardware sd card port issue

    still need sd card for the main stuff, unless things have changed from when I last read about sxos and usb support or I totally read it wrong. anyway on a brighter note I seemed to of repaired my module now. only needed 1 wire solder from mobo dat2 pad going to the module dat2 point. the...
  9. M-O-B

    Hardware sd card port issue

    looking for but if info on the sd card module port on the switch mobo. I seem to have 2 pins missing, and can no long use any sd card, strange how this has happened coz it was working fine for a couple off hours after I put the switch back together. anyway what I'm looking for is a way to...
  10. M-O-B

    Tutorial Trinket Internal Install.

    I'd remove all wires and solder them again, but 1 by one to each point, so you don't get the data wires mixed up. also make sure you have the drivers installed on your pc for the switchMe, not sure if it uses the same drivers as the trinket as never bothered with that chip. this should give...
  11. M-O-B

    Tutorial Trinket Internal Install.

    forgot to post this better late than never. hekate 4.2 uf2 drag and drop files
  12. M-O-B

    Tutorial Trinket Internal Install.

    no probs a note to anyone the fusee-primary bin worked when I was on 5.1, but since I've updated to 6.0 it no longer loads. all other payloads tested and work on 6.0
  13. M-O-B

    Tutorial Trinket Internal Install.

    ok here this package has all latest payloads. sxos, hekate 4.1, ReiNX, RajNX and atmosphere aka fusee-primary bin. these are uf2 drag and drop files only
  14. M-O-B

    Tutorial Universal CFW instalation guide

    I think a 10k resistor between pin 7 & pin 10 in the joycon would be better than just direct pin bridged. I had 10k on pin7 & pin 10 for a couple on months now without any issues..
  15. M-O-B

    Tutorial How To Flash The Trinket M0 Using Arduino

    some more dongle uf2 drag and drop files. these will work on the R4 dongle and trinket and gemma these are individual payloads and ReiNX in compiled from the source this morning. I will add these to the op once I sorted the multi payloads out. plus going to put most my time into an internal...
See more
General chit-chat
Help Users
    BakerMan @ BakerMan: (this is going to be horribly misinterpreted as me wanting to fuck DK or smth, isn't it?)