Recent content by longson008

  1. L

    Switch charges but no signal on dock

    Hi! Have a switch that charges both side. Changed usb c port and works fine. Touch sensor and no signal on dock mode. Changed usb c 2 power chip and p13usb chip. All filters are fine one the back . Any ideas? Longson
  2. L

    Switch V2 apu cap solder tips

    Switch still running fine
  3. L

    Switch V2 apu cap solder tips

    Hi! Any tips how to solder on the new capacitator on switch apu? Tried hot air and it doesn't sticks. Tried 420c. Solder station max 480 ant it sticks sometimes but hardly on the cap. Longson
  4. L

    Switch V2 picofly works a while then stuck on logo ofw and after atmopshere logo

    It's a legit Samsung sd micro. Tri d now and restoration. Could run all restore steps on emunand but not on sysnand. Comes to the point where emunand cfw seems to running fine but cannot read the atmopshere files because after wipe it requires system update to be able to run bigger sd cards...
  5. L

    Switch V2 picofly works a while then stuck on logo ofw and after atmopshere logo

    Installed flex and no more slow mode and could make emummc. Can't start ofw stuck on switch logo and cfw stuck after atmopshere logo. Please help
  6. L

    Switch V2 picofly works a while then stuck on logo ofw and after atmopshere logo

    Have a switch v2 worked perfectly for a while. Then it stopped working. Picofly chip do works and can go to Hekate. Can make backup and no errors Cannot emummc because slower mode hardware issue. Cannot blot ofw via Hekate upstart. Help. Longson
  7. L

    Switch V2 and switch lite won't start ofw after picofly fail

    Have 2 switch i can't get to ofw after removing the chips and cables Switch V2 Switch lite Both where running great and suddenly stopped working. Both was running again efter resoldering all the points. After fine adjustments both won't glitch. Gives me purple light. Now it won't go to ofw...
  8. L

    Picofly short short long

    Had my switch running for a few days. Both lite and V2. Suddenly both stopped working. Think that my flux is bad and replaced it and cleaned out old stuff. Now mämy V2 won't start at all even if chip is removed. Black screen . Gives me 2.76 purple and 2.74 short short long. Hacked 2 other V2 and...
  9. L

    Switch lite picofly problem short long long

    Resolder my mosfet chip 1685266423 Had this problem on a switch V2 again. Didn't work with 2.73. but did work with 2.74.
  10. L

    Switch lite picofly problem short long long

    My faulty chips now works. Was mosfet soldering was the problem
  11. L

    Switch lite picofly problem short long long

    I still have this problem on a working one. Suddenly stopped working and shows this code. Tested 5 chips same result. I might have too long cables on rst cmd clk and do. Will try again tonight
  12. L

    Picofly rp2040 faulty

    Thanks for the tips! I was actually looking for a reset. I'll give it a try and give you the result! Longson 1685039134 Nuke it didn't work :(
  13. L

    Picofly rp2040 faulty

    Hi! I encounter 2 faulty chips recently. The one that's faulty have been reflashed with different fw just drag and drop. Change to a new chip and dropped 2.73 and work instantly. Did i do something wrong with the reflashing ones or was they just faulty? Longson
  14. L

    Switch lite picofly problem short long long

    Thanks everyone. Last attempt was to change rp2040. It did work! Maybe flux or cold soldering on the chip. The solder points where perfekt on board. Used one mosfet and it all went good.
  15. L

    Switch lite picofly problem short long long

    It's a switch lite with picofly flash with 2.73
See more