Recent content by joaoneves

  1. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    And which good adapters can I use? Is there any photo where I can see which ones are good? Thank you
  2. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    The issue was indeed with the dat0 point, BUT it wasn’t due to a bad solder joint. The culprit was the dat0 flex cable, as you can see—on the left is the faulty flex. When the switch heated up, the solder balls would expand, and it would end up picking up some other value from a nearby point...
  3. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    Não encontrei esse erro no guia do Picofly; alguém pode me ajudar a entender do que se trata? No FW 2.73, ele piscava um amarelo longo, amarelo curto = dat0. Após a atualização para 2.80, ele pisca de forma diferente: longo, curto, longo, curto. Qualquer um?
  4. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    I noticed an unlocking behavior where it enters Hekate repeatedly if the device is COLD, but after warming up, it shows a long yellow error, followed by a short yellow error 'Dat0 not connected.' Could the flex cable connected to the NAND expand after heating up? In that case, the flex might...
  5. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    What is the minimum size required for the creation to back up the NAND of the OLED model? Can I do it with less than the original capacity of 59GB? I'm asking because on the Switch v1, v2, and Lite, I used the minimum size of 12GB, which corresponds to the size that the original system occupies.
  6. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    Montei o switch inteiro e coloquei o invólucro externo. Eu também verifiquei essa parte USB na parte inferior da placa. A questão é: seria melhor desmontar o interruptor e colocá-lo no lugar, ou o interruptor ficará bem sem isso? Essa blindagem protege o USB de curto-circuito ou algo assim, ou...
  7. joaoneves

    RP2040 Install clk value ok or not?

    Montei o switch inteiro e coloquei o invólucro externo. Eu também verifiquei essa parte USB na parte inferior da placa. A questão é: seria melhor desmontar o interruptor e colocá-lo no lugar, ou o interruptor ficará bem sem isso? Essa blindagem protege o USB de curto-circuito ou algo assim, ou...
  8. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    I thought the readings were high because the dat0 cable was connected to the chip. I removed the dat0 cable from the chip and got the correct value of 0.862. After confirming everything was correct, I re-soldered it, and it started working again multiple times; I did at least 10 boots that...
  9. joaoneves

    Hacking Hardware Picofly - a HWFLY switch modchip

    I made the modification on the OLED switch, and after soldering all the points and making the connections with the chip, everything worked very well; the 'No SD card' screen appeared repeatedly. My problem started after I began reassembling the Nintendo. After placing the copper heatsink and...
  10. joaoneves

    Hacking SWITCH NOOB PARADISE - Ask questions here

    can i get the clk point (d) from somewhere else, on switch lite? The pads were removed from that location and I don't think you can jumper other than on the nand, does it pass nearby trails?
See more