Recent content by dewolf

  1. dewolf

    ps5 EDM-041 - uart 80801101 & 80801601

    Hello Everyone, thanks to @stetofix i did an analysis on RAM pad.. some wrong value... so i did a full reball of the ram chip and a REFLOW of the APU, it start working perfectly :) first of that @alex1kgr please check all other common cause ( Fuse, voltage line, short on common capacitor...
  2. dewolf

    Awoo-Installer Forwarder

    can you repost it?
  3. dewolf

    ps5 EDM-041 - uart 80801101 & 80801601

    thanks dude, i'll try and let you know :)
  4. dewolf

    ps5 EDM-041 - uart 80801101 & 80801601

    Hello! i've a Ps5 Slim EDM-041 with 1 Beep, Blue light for 2-3 sec and then Power off. it's my first time to attemp a repair of a PS5 (i've expirience with nintendo console and other electronic stuff) i've : - checked all the fuse (ok) - check main line from the power (no short) - check...
  5. dewolf

    Read firmware FROM HWFLY/Instinct/GD32 chip

    i need to clone the firmware from a chip to another one... and just for curiosity if it is possible ;)
  6. dewolf

    Read firmware FROM HWFLY/Instinct/GD32 chip

    ok so there is no way to extract firmware without a programmer? i mean, we can write with the firmwareupdater.exe but we can't read from it ?
  7. dewolf

    Read firmware FROM HWFLY/Instinct/GD32 chip

    i've just the chip connected to the USB port (via the usb cable) so no programmer, i've tested with GD-LINK but i get always no connection, did you've any guide that i can follow? i need to extract the ISTINCT-NX firmware from the chip since i can't find anywere
  8. dewolf

    Read firmware FROM HWFLY/Instinct/GD32 chip

    hello everyone, as anyone know.. there is any chance to get the Firmware from a chip? i need to extract firmware and bootloader from an Instinct V6 but i can't find any clue
  9. dewolf

    Short on "D" - CLK Point will kill your switch?

    Reading is good, the CLK point connect just cpu and emmc? There is no other component involved ? 1697379210 Nope, I’ve check :)
  10. dewolf

    Short on "D" - CLK Point will kill your switch?

    Hello Everyone, (sorry for my bad english <3 ) i'll start this thread since there is some general discussion but nothing specific on this point. i've received a couple of switch to repair that goes in black screen after a short on the "D" - CLK point (customer tried to install...
  11. dewolf

    Hardware Accidentally Removed Resistor Below The RST Solder points

    console don't boot up without that resistor installed
  12. dewolf

    Picofly (RP2040) OLED getting error Failed to init eMMC. But with HWFLY working fine.

    Thanks god someone trust me <3 :)
  13. dewolf

    Picofly (RP2040) OLED getting error Failed to init eMMC. But with HWFLY working fine.

    But how can be an hardware issue??? IF I INSTALL AN HWFLY ON A PURPLE SCREEN AFTER A PICOFLY, the console start works PERFECTLY Pico have some trouble with BIS keys, or partition, or I don’t know… sometimes just mess your EMMC…
  14. dewolf

    Picofly (RP2040) OLED getting error Failed to init eMMC. But with HWFLY working fine.

    always purple, with or without chip... installing HWFLY it fix something... and after if you remove the chip it start normally in stock
  15. dewolf

    HWFLY OLED / Battery 0% - Hekate doesn't show temp too.

    reflow the EMMC yes, same result, reflow the APU no... but why to do that? i mean... console boot into hekate, everything works (also the emmc backup) just it go to 0% battery... i don't think that is related with the cpu... no?
See more