Recent content by DeltaDan

  1. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    An update: Thank you to everyone who commented to help me figure out what was going on. I tested the switch by trying to run payloads, I figured if i could get into Lockpick or Hekate or something, I could fix the NAND, but the only payload that would run was UMS. Which specifically says that...
  2. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    I used a needle to pop it open, I didnt think I went that deep with though. But im ordering a better soldering kit and a magnifying camera (im surprised i got this far with the tools i had) so i can fix the traces. I think I saw somewhere someone used the fine wire you get in headphone wires to...
  3. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    How else can I answer it? It boots into Hekate when that SD card is put into my v1 switch, and the payload is launched through tegrarcm 1761178395 Ive discovered the issue, I somehow managed to scratch a trace on the ram, probably when taking off the shield. :glare:
  4. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    Yes, I used the SD card on my v1 switch with an RCM jig and loading the payload
  5. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    If an sd card isnt in, it flashes like this and goes to the "no sd card" screen. But if one Is in, but empty, I get "failed to load payload.bin" BUT if the sd card has files and a payload.bin... nothing. But they all flash the same way 1761169192 This is what currently happens: No SD card...
  6. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    What currently happens is this with an SD card in. But the screen remains black.
  7. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    Just a quick one too, will the picofly boot with a corrupted NAND? I tried booting with an sd card in with a payload on the root of the SD card, but nothing happens
  8. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    What can I do now? Is it possible to get the switch into RCM mode with the rp2040?
  9. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    I didn’t no, I had no way to do it it’s a v2 switch. Unless you can interface the nand using the picofly board with the usb c?
  10. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    What I’m going to try and do is re install the modchip, and get the lockpick payload in. Is it at all possible to get the switch into RCM mode or does lockpick bin need to be on the root of the sd card to Boot
  11. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    When I hold VOL + - i get a blue screen
  12. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    Yep, but with rp2040 in i get no sd screen
  13. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    But what could be causing the blue screen when booting into OFW?
  14. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    I dont think its that, I tested it on my v1 switch, putting that sd card in with RCM and they booted fine
  15. D

    Picofly rp2040 installed on a V2 switch, get to no sd card screen, but cant boot from SD or into OFW

    So I got a picofly rp2040 from ali express the other day, installed it onto my switch ensuring i was being super careful lifting the shield and soldering, after I finished that I turned it on and was happily met with the "no sd card" screen with the picofly symbol, but when I put an SD card...
See more