Recent content by Akwiz

  1. A

    Hacking Hekate will not load!

    No I checked the album and it tells me there are no screenshots taken on this device. auto Atmosphere. Whatever version is in the Kosmos 12.2 release. auto Also, just an update. I switched my USB cable. I think something was wrong with it. My payload pushes faster and reliably now and I get...
  2. A

    Hacking Hekate will not load!

    Alright so that did allow me to get into the Hekate menu. After which I boot to CFW and it goes through the loading text, I get the green at the bottom... and then switch logo. Boots to OFW. :( auto Maybe I will try with exfat?
  3. A

    Hacking Hekate will not load!

    Yes, it was a totally new SD with nothing on it. I did boot into OFW to get the Nintendo folder but its just the 12.2 release from Atlas and nothing else.
  4. A

    Hacking Hekate will not load!

    So. The Hekate 4.10.1.bin causes TegraRCM to hang and crash. Downloaded the latest Tegra to 2.5 and now it does push the payload successfully but I just get a black screen. Like its just sitting in RCM mode doing nothing. From my Tegra: RCM device disconnected RCM Device detected Invoking...
  5. A

    Hacking Hekate will not load!

    Thanks, Ill try it now.
  6. A

    Hacking Hekate will not load!

    Hello all. So I have a switch that is susceptible to fusse-gelee on 6.2.0. Freshly initialized. I have a FAT32 SD that I have loaded fresh with Atmosphere from sdsetup.com. I can boot into RCM and push Hekate 4.9.1. It works. Flashes the Atmosphere logo a bunch of times and in small text says...
  7. A

    Hacking CFW boot stuck at PKG1 found.. nothing changed

    Thank you! I will try that. So just leave Nintendo? Thanks
  8. A

    Hacking CFW boot stuck at PKG1 found.. nothing changed

    Update... I let it sit at PKG1 found for 15-20 minutes and it eventually booted. If anyone has any input why. If not maybe this post can help others with the same problem.
  9. A

    Hacking CFW boot stuck at PKG1 found.. nothing changed

    Whats up dudes, So This morning I installed a new nsp and thats it. Nothing else changed but tinfoil did crash my device at once point and hekate would not boot my CFW afterwards. It would get stuck at PKG1 found.... and was stuck there forever. The weird thing was after about 10 tries it just...
  10. A

    Hacking Brick 7.0.1 update

    For anyone who has been following or having similar issues: The ONLY thing I have gotten to work is tinfoil 0.2.1 and Fluffy with a USB-a to USB-C cable. USB-c to USB-c does not work. So thanks to everyone who helped out!
  11. A

    Homebrew RELEASE Fluffy - A Tinfoil and Goldleaf GUI

    Bought a new cable. Looks like usbc to usbc doesn't play nice. Detected now :)
  12. A

    Hacking Brick 7.0.1 update

    Hey thanks. Looking into fluffy now! Will keep you posted. auto Right. I am having such a hard time since then. I am considering going back to 6.2 and starting over.
  13. A

    Homebrew RELEASE Fluffy - A Tinfoil and Goldleaf GUI

    Hey guys. I am still getting "Switch not detected". I have installed the drivers 10 times. I have tried tinfoil 1.0, 0.2.1, goldleaf 0.2 and goldleaf0.5. Not sure what I am missing. My usb cable is USB-c to USB-c. Not sure if I should try a USB-C to USB-A? Any ideas?
  14. A

    Hacking Brick 7.0.1 update

    Damn. So basically everything on my SD is toast. Have to reinstall. Some NSP install no problem. Others I get: "Ïnvalid NCA Magic. (missing sig pathces?) (Firmware too low?)" I have used the sig patches from the kosmos release site and linked above in this thread. At a loss at this point.
  15. A

    Hacking Brick 7.0.1 update

    Okay, so apparently after installing 7.0 with choidujorNX it enabled autoRCM automatically? I just tried booting without my jig in my switch at all and it seems to have booted! Why would the jig stop it from booting . Side note, none of the NSPs previously installed on my nand want to run...
See more