Hacking Question Help with black screen and battery. Please read.

[Styledvinny]

Hi everyone. I really hope someone can help me.

I went away about four weeks ago and haven't used switch since. Basically it will have drained and was in Rcm mode.

I've tried to turn on. Nothing.

1. I have disconnected and reconnected battery.
2. I have held power button down forever and nothing.
3. I have left to charge for days even though it was in rcm mode.

I can...

1. Install payload on pc using tegra. But after installing it stays on black screen.

If I remove the sd card and then install payload it comes with the red boot. Dat screen. This makes me think battery is ok.

Points.

1. I am super banned and it is not on 6.2 even though I technically cannot tell nor remember if WiFi was switched off. So it may have updated BUT I don't know.

3. I cannot even access the sxos menu once pay load installed by pressing up on volume

I really am stuck. No idea whatsoever.

Could someone help me out. Thanks!!

 

[bk300]

Looks like it is run out battery. If run out battery you can use tegar. To Inject hekate_fspatches_v3.bin.
After boot in to Hekate screen stay in screen don't do anything. On Hekate screen your switch will able to charge.

Hekate link: https://github.com/rajkosto/hekate/releases

Edit: Don't remove your sd card when you inject it.

 

[Styledvinny]

Thank you. I did that and my battery is at 96 per cent.

I have no idea why it won't boot into normal or sxos at all.

It is accepting payloads. Just nothing is happening bur at least i know juice is in the battery

 

[Styledvinny]

So for some reason. My switch having not been used for weeks, has 100 percent battery., screen works to show ctcaer payload, but will not load any cfw or official firmware.

Just goes black. But isn't a screen issue or a battery issue



QUOTE="Styledvinny, post: 8398166, member: 471311"]Thank you. I did that and my battery is at 96 per cent.

I have no idea why it won't boot into normal or sxos at all.

It is accepting payloads. Just nothing is happening bur at least i know juice is in the battery[/QUOTE]

 

[bk300]

So for some reason. My switch having not been used for weeks, has 100 percent battery., screen works to show ctcaer payload, but will not load any cfw or official firmware.

Just goes black. But isn't a screen issue or a battery issue



QUOTE="Styledvinny, post: 8398166, member: 471311"]Thank you. I did that and my battery is at 96 per cent.

I have no idea why it won't boot into normal or sxos at all.

It is accepting payloads. Just nothing is happening bur at least i know juice is in the battery

[/QUOTE]

Ok. if you don't mind delete all your data from your switch, you can try this.
1.Use Hekate to fully shut down your switch.
2.hold the Volume Up + Volume down at the same time.
3.Inject the payload.
After that it should boot in to "Recovery mode" than do the "Restore factory settings".

 

[Styledvinny]

Hi. I've done what you said and it doesn't bring up recovery mode. Just the normal screen. Attached image


Ok. if you don't mind delete all your data from your switch, you can try this.
1.Use Hekate to fully shut down your switch.
2.hold the Volume Up + Volume down at the same time.
3.Inject the payload.
After that it should boot in to "Recovery mode" than do the "Restore factory settings".[/QUOTE]

 

[bk300]

Hi. I've done what you said and it doesn't bring up recovery mode. Just the normal screen. Attached image



Ok. if you don't mind delete all your data from your switch, you can try this.
1.Use Hekate to fully shut down your switch.
2.hold the Volume Up + Volume down at the same time.
3.Inject the payload.
After that it should boot in to "Recovery mode" than do the "Restore factory settings".

[/QUOTE]

Ok. on step 3. Inject the ReiNX.bin.
Link:https://github.com/Reisyukaku/ReiNX/releases


Edit: Make sure you hold the hold the Volume Up + Volume down at the same time in correctly.

 

[Styledvinny]

Attached Image after doing what you said

--------------------- MERGED ---------------------------

Attached Image after doing what you said

--------------------- MERGED ---------------------------

Now patching OS through Rein. No idea what has happened to it at all.

 

[bk300]

Attached Image after doing what you said

Because your ReiNX set up was incorrect. I am going to packaging my ReiNX to you. You can just unzip it and put it into your sd card.

ok just finished upload here you go : https://drive.google.com/open?id=1tvgR4pJAQHHgvIYil5MphiF21aPclMAI

 

[Styledvinny]

Shall I just shut this fully down and inject yours onto mine?

Again thank you for all your help.
No idea what has happened. Worked fine in Spain but not used for weeks

 

[bk300]

Shall I just shut this fully down and inject yours onto mine?

Again thank you for all your help.
No idea what has happened. Worked fine in Spain but not used for weeks

yes fully shut down. Make sure you hold the hold the Volume Up + Volume down at the same time before you inject ReiNX.bin.

do not release the Volume Up + Volume down before you inject.

 

[Styledvinny]

Thank you.

It is currently reading packages.

yes fully shut down. Make sure you hold the hold the Volume Up + Volume down at the same time before you inject ReiNX.bin.

do not release the Volume Up + Volume down before you inject.

I'm

--------------------- MERGED ---------------------------

Attached so far

--------------------- MERGED ---------------------------

Failed to read GPT whatever that is

Thank you.

It is currently reading packages.


I'm

--------------------- MERGED ---------------------------

Attached so far

 

[bk300]

Thank you.

It is currently reading packages.


I'm

--------------------- MERGED ---------------------------

Attached so far

--------------------- MERGED ---------------------------

Failed to read GPT whatever that is

OMG. Looks like it can not read internal storage. Normally GPT meaning GUID Partition Table.

 

[Styledvinny]

No idea why at all as it hasn't been used and last time on it worked.

Any ideas what I can do

OMG. Looks like it can not read internal storage. Normally GPT meaning GUID Partition Table.

 

[blahblah]

The thing about not being able to charge while in RCM is a myth. Put the Switch on the official Nintendo charger. It will charge. Looks like your switch is all kinds of messed up.

 

[bk300]

Thank you.

It is currently reading packages.


I'm

--------------------- MERGED ---------------------------

Attached so far

--------------------- MERGED ---------------------------

Failed to read GPT whatever that is

Try to use the Hekate to bump RAM eMMC. If work meaning the internal storage still work.

1.Inject hekate_fspatches_v3.bin
2.go to tools
3.bump RAM eMMC

--------------------- MERGED ---------------------------

The thing about not being able to charge while in RCM is a myth. Put the Switch on the official Nintendo charger. It will charge. Looks like your switch is all kinds of messed up.

No. His battery is at 100 per cents. Maybe something wrong.

 

[Styledvinny]

Is it this one?

Try to use the Hekate to bump RAM eMMC. If work meaning the internal storage still work.

1.Inject hekate_fspatches_v3.bin
2.go to tools
3.bump RAM eMMC

--------------------- MERGED ---------------------------


No. His battery is at 100 per cents. Maybe something wrong.

 

[blahblah]

Try to use the Hekate to bump RAM eMMC. If work meaning the internal storage still work.

--------------------- MERGED ---------------------------


No. His battery is at 100 per cents. Maybe something wrong.

Yeah, that's what I'm saying. His Switch is all screwed up. Looks like an eMMC failure.

 

[bk300]

Is it this one?

No, Go to "back up" not "restore".

 

[Styledvinny]

Sorry which one

No, Go to "back up" not "restore".