Homebrew Running Ninjhax 1 & 2

[kontrolaltdelete]

Just curious if there are any methods to run both simultaneously (one on sysNAND for my 9.0 N3DS and Ninjhax 2 for emuNAND)? I know from a few threads here that people discussed different methods (creating two folders and moving the 3dsx files back and forth) but I was curious if there might be an easier solution. I'd like to be able to run Homebrew on my emuNAND at 9.5, but not lose the control I have over my sysNAND Homebrew.

 

[MassExplosion213]

Just curious if there are any methods to run both simultaneously (one on sysNAND for my 9.2 N3DS and Ninjhax 2 for emuNAND)? I know from a few threads here that people discussed different methods (creating two folders and moving the 3dsx files back and forth) but I was curious if there might be an easier solution. I'd like to be able to run Homebrew on my emuNAND at 9.5, but not lose the control I have over my sysNAND Homebrew.

What's your firmware version?

 

[kontrolaltdelete]

What's your firmware version?

9.0 sysNAND N3DS and 9.5 emuNAND.

 

[MassExplosion213]

US sysnand?

 

[kontrolaltdelete]

US sysnand?

Yep. Obviously both are US.

Quick edit: my SysNAND is 9.0. My bad.

 

[MassExplosion213]

Yep. Obviously both are US.

Run SaveDataFiler on your cubic ninja cart and pm me the payload.

 

[kontrolaltdelete]

W

Run SaveDataFiler on your cubic ninja cart and pm me the payload.

Sweet. Will do when I get the chance. I'm pulling a 24 hour shift right now, but I'm trying to figure some stuff out for when I get back home. Thanks mate. I didn't expect I'd actually get an answer or help so quick.

 

[MassExplosion213]

W


Sweet. Will do when I get the chance. I'm pulling a 24 hour shift right now, but I'm trying to figure some stuff out for when I get back home. Thanks mate. I didn't expect I'd actually get an answer or help so quick.

No prob. I'll pm you my modified boot.3dsx too. Leave it named as is. The payload loads boo1.3dsx, which is my modified boot.3dsx. It loads all Ninjhax 1.1 payloads from 3ds1.

 

[MassExplosion213]

Modded boot.3dsx.
https://mega.nz/#!RtNg2ZLT!DwhvCHbXO4Y7mSi_8S9zHZv9ZAY12SklszFqbl8t1ug

 

[kontrolaltdelete]

Thanks again. I'll pm you the dump in a few hours now (close to being done). Does it need to be the payload from emuNAND or sys? And finally, should I have run Ninjhax before, or does it matter? ie on emuNAND I haven't run Ninjhax 2.0 yet (1.1 worked fine though before I upgraded to 9.5)

 

[MassExplosion213]

Thanks again. I'll pm you the dump in a few hours now (close to being done). Does it need to be the payload from emuNAND or sys? And finally, should I have run Ninjhax before, or does it matter? ie on emuNAND I haven't run Ninjhax 2.0 yet (1.1 worked fine though before I upgraded to 9.5)

It has to be sysnand. And it doesn't have to be run before.

 

[fmkid]

My suggestion (at least, running Ninjhax 2.x) is put any boot.3dx HB Loader files into "3ds" folder (different named and/or in different folders), to load each one same way as a typical homebrew does.

 

[MassExplosion213]

My suggestion (at least, running Ninjhax 2.x) is put any boot.3dx HB Loader files into "3ds" folder (different named and/or in different folders), to load each one same way as a typical homebrew does.

I'm just modifying a 1.x payload to load a file called boo1.3dsx instead of boot.3dsx. The boo1.3dsx is a modified launcher that loads all homebrew from a directory called 3ds1. That way, Ninjhax 2 can still load boot.3dsx and load homebrew from the 3ds directory.

 

[fmkid]

I'm just modifying a 1.x payload to load a file called boo1.3dsx instead of boot.3dsx. The boo1.3dsx is a modified launcher that loads all homebrew from a directory called 3ds1. That way, Ninjhax 2 can still load boot.3dsx and load homebrew from the 3ds directory.

Interesting! But, how I can use that file? Where on my SD card should I put?

 

[MassExplosion213]

Interesting! But, how I can use that file? Where on my SD card should I put?

The modified payload?

 

[fmkid]

boo1.3dsx file, yes!

 

[MassExplosion213]

boo1.3dsx file, yes!

Ok, to use boo1.3dsx, you have to have a modified payload on your cubic ninja cart. The boo1.3dsx file goes on the root. Run SDF on a cubic ninja cart with ninjhax 1 on it and pm me the payload.bin.

 

[fmkid]

Well, sorry, but really I'm using IronHax (O3DS 9.9U) ... Mention that, Is possible use your boo1.3dsx with that exploit, or is doesn't usefull?

 

[MassExplosion213]

Well, sorry, but really I'm using IronHax (O3DS 9.9U) ... Mention that, Is possible use your boo1.3dsx with that exploit, or is doesn't usefull?

Not useful. Idk if that payload is modified. But if it is, you could have multiple slots loading boo1.3dsx and boo2.3dsx. Those could load from 3ds1 and 3ds2. It could be useful. You want me to look into it?

 

[fmkid]

Not useful. Idk if that payload is modified. But if it is, you could have multiple slots loading boo1.3dsx and boo2.3dsx. Those could load from 3ds1 and 3ds2. It could be useful. You want me to look into it?

If you can do it, I suppose that will be great!