Search results

  1. Jagovi

    Hacking Hardware Switch OLED SkHynix with Picofly long boot-time

    I have exactly the same problem. I have used the kamikaze method. All diode value are ok. But sometimes I get === in glitching attemps without lucky; and others it launch hekate without problems taking between 2-80 secs
  2. Jagovi

    Hacking Hardware Switch OLED Picofly Issue: Error 2016-0641, SD Card Not Working

    Yes!!! Thank you so much!!!!
  3. Jagovi

    Hacking Hardware Switch OLED Picofly Issue: Error 2016-0641, SD Card Not Working

    The values looks similar except the second and the last point (From left to right). And it wouldnt be GND.... Where does that signal come from? 1734011996 1734019864 Update! I see that the pin 9 (grounded) go directly to the CPU. So I made a reflow and it is working again. Thanks!!!
  4. Jagovi

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi everyone, I recently installed a Picofly modchip on my OLED Switch using the Kamikaze method. Everything went fine, and the console was working great for two days in both OFW and CFW. Last night, I left the console installing some games using DBI, but this morning, I found an error on the...
  5. Jagovi

    Hacking Hardware Switch OLED Picofly Issue: Error 2016-0641, SD Card Not Working

    Hi everyone, I recently installed a Picofly modchip on my OLED Switch using the Kamikaze method. Everything went fine, and the console was working great for two days in both OFW and CFW. Last night, I left the console installing some games using DBI, but this morning, I found an error on the...
  6. Jagovi

    Hardware Intermittent Charging Issue on Nintendo Switch V1

    I have tried to move the USB C cable but nothing change, intermittent charge. I will replace it but the values of continuity look well
  7. Jagovi

    Hardware Intermittent Charging Issue on Nintendo Switch V1

    I have a Nintendo Switch V1 that wasn’t charging. I replaced the M92T36, and it has improved but not completely. Now, it only charges when it’s in the dock. When it's outside of the dock, it charges intermittently: it shows that it's charging for 5 seconds, stops for 1/4 of a second and appears...
  8. Jagovi

    Hardware Left joy-con not recognized OLED version

    Hi everyone! I bought a Nintendo Switch OLED with a broken touch screen from an alleged impact. It was cheap, and I had a spare screen, so I decided to get it. When it arrived, I tested it, and everything worked except for the touch screen, and it didn't recognize the left Joy-Con when it was...
  9. Jagovi

    OLED Switch Joycon not connecting when docked. What is damaged?

    I have the same problem but with the left joycon…. Rail it’s ok, joycon it’s ok. FPC doesn’t have damages. What should be the next to test? Solved. I resoldered the fpc conector.
  10. Jagovi

    Problem in 3.3V instinct always flashing red

    Before of getting the error was functioning with the flex. In my opinion, the problem is with the 3,3v line. But I don’t know how can find the issue.
  11. Jagovi

    Problem in 3.3V instinct always flashing red

    Yes, it is bottling without problems en OFW
  12. Jagovi

    Problem in 3.3V instinct always flashing red

    When I press the power button, yes, the console turns on in OFW. But without pressing the power button, it's the chip that tries to glitch erroneously.
  13. Jagovi

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have two short flashes. I have the board removed from the console. I connect the processor flex, the cable from the 3.3V (I'm not connecting the other points, just individual cables), and then the battery connector. Immediately after this, the chip lights up blue and gives two yellow flashes...
  14. Jagovi

    Problem in 3.3V instinct always flashing red

    I have removed the dat0 and make kamikaze method with the same result. I connect the processor flex, the cable from the 3.3V (I'm not connecting the other points, just individual cables), and then the battery connector. Immediately after this, the chip lights up blue and gives two yellow...
  15. Jagovi

    Problem in 3.3V instinct always flashing red

    I just checked that if I don't connect the CPU flex to the chip, the error doesn't occur. I changed the flex for another one, but it remains the same. The moment I connect the battery with the CPU flex connected, the chip starts trying to glitch even if I don't press the power button. If I don't...
  16. Jagovi

    Hacking Hardware Picofly - a HWFLY switch modchip

    How can I Fix it? What should i do? 1721041423 I just checked that if I don't connect the CPU flex to the chip, the error doesn't occur. I changed the flex for another one, but it remains the same. The moment I connect the battery with the CPU flex connected, the chip starts trying to glitch...
  17. Jagovi

    Hacking Hardware Picofly - a HWFLY switch modchip

    Could you help me, please? Thanks!!!
  18. Jagovi

    Problem in 3.3V instinct always flashing red

    I have updated the first message with images. To try to narrow down the problem, I removed the DAT0 adapter, replaced the Instinct with a Picofly, and disconnected all the connections. I connected only the 3.3V and ground to the chip, leaving the rest disconnected. It does the same thing... As...
  19. Jagovi

    Problem in 3.3V instinct always flashing red

    Hi everyone, I've been using a Nintendo Switch OLED with Instinct for 5 months without any issues, but today it stopped working. It only powers on in OFW and constantly blinks red, even when the console is turned off. I tried replacing the chip with a Picofly. When I connect it, even with the...
  20. Jagovi

    Hacking Hardware Picofly - a HWFLY switch modchip

    Could you help me? I'm having an issue with my Nintendo Switch. What could be the reason for having voltage in the 3.3V caps without pressing the start button? Additionally, why does the chip turn on just by connecting the battery? Only turn on the chip, the Nintendo switch stay turned off.