Search results

  1. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I always remove 3.3v regulator when installing picofly. The short on rp2040 board is gone after I removed the bad caps. 1694270003
  2. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    Today I got a problem that my friend's switch could not power on. After measuring I realized that it had a short on 3.3v and ground, a caps on picofly died. Remove the picofly and switch boot again. Anyone know which caused that caps shorted? 🧐
  3. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    led indicator and capacitors may be not required but the small chip in center of the board is flash chip (where the code store) is very important, Idk resistor is required or not
  4. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I don't think my soldering job had something wrong. I think the problem is the mosfet, yesterday It couldn't glitch anymore, so I replaced it.
  5. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    @rehius I have a good news today, the cyan led issue on my friend's mariko has gone 🤣 I replace old double mosfet with only 1 new mosfet and now it can boot to hekate normally, no more need clicking reset button
  6. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    Sorry for bothering you, any positive sign on cyan led issue?
  7. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    1681916015 Idk. You can trace the line to 2 upper point which the capacitors connected to, make sure not cut the line. you must connect 2 anchor point to the frame (it connects to GND and source of the mosfet) due to 2 lower point has been cut off. 1681917086 my friend's v2 using samsung emmc...
  8. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    v2. lite, oled use the same flex cable, so if he modded for v2, it also works on lite
  9. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    yes, there are someone have already done that in this thread 1681914313 switch can work normally without this cap. you should get continuity if you have already connect the mosfet to capacitor
  10. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I will send its information when I get back home. I have 3 consoles, my v2, my friend's v2 and lite. My first v2 used hwfly flex cable, and It work like a charm without any problem with firmware 2.5 + unlock.uf2 My friend v2 got an issue which always got cyan led and need to click the reset...
  11. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I faced the same problem yesterday, tried to re-soldering many times but got the same yellow light, and then I click reset button on my rp 2040 one, and tada it glitch normally again. you can try if you want.
  12. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    every size of 47R should work
  13. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    but It glitched successful without sd card or empty sd card :(
  14. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    My switch lite can get in to no sd card screen but it can't boot to hekate and keep glitching (blue blink -> green loop). I'm using fw 2.65.
  15. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    when I flashed 2.6, no led indicator in rp2040 and no thing happened even clicking reset button. @rehius thanks for new 2.64, I will try it tomorrow. I `I've just removed the mosfet and take a break today :D 1681405894 oh my friend's v2 using samsung emmc :rofl2: checked in hekate.
  16. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have a lot of 0201 1uf 6.3v cap so it's not a problem, just too lazy to solder it back, too tiny 🤣 maybe I will try a thicker wire. In my local forum, they are using 0.1mm without any problem 😓 1681320931 But why it worked when I click reset button :(
  17. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I'm using 0.1mm enameled wire. I 've just pulled off sp1 cap while trying to solder the broken wire (but thing goes as the same as before (when the cap still there))
  18. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    Already installed 2 mosfet :(
  19. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    You mean power options -> restart? I 've just tried that but it didn't work
  20. haipro287

    Hacking Hardware Picofly - a HWFLY switch modchip

    I am having problem while installing rp2040 zero with mosfet for my friend's mariko. The mod chip always shows blue-> cyan (I guess) and boots to OFW. but when Nintendo logo appears, click reset button in rp2040, it starts glitching and tada: green led + boots to hekate. It's look like @Rodel...
General chit-chat
Help Users
    Xdqwerty @ Xdqwerty: @SylverReZ, @K3Nv2 https://youtu.be/_b_WmfLhnMM?si=1GZF2ULEvDAH418O +1