Search results

  1. P

    Hardware Switch no power at all

    Switch has no power, bought as defective unit, m92 pin 5 and 6 are pushing around 3.4v bq chip is pushing around 14v. The fuse that's infront of the charger port does not beep on continuity mode. The "coil/inductor I'm guessing?" To the left of bq is getting very hot, burn to the touch. Obvious...
  2. P

    Hardware Nintendo logo comes and goes back

    Sounds like the bq or m92 chip again. Check pin 5 and 6 on m92 and make sure your getting somewhere around 3.3v while plugged up. Check for shorts around those area too. The logo showing up but then black sounds like the bq to me tho
  3. P

    Hardware Nintendo switch v1 Power supply instead of battery

    Can you send a picture of the pads? Do you have any repair shops near you? Also, you in theory could solder the usbc wire to the console, but utd have to go onto those pads to be effective... according to what pads are ripped they can be fixed.
  4. P

    Hardware Does bad/fake m92t makes battery drain fast?

    So I'm not sure if anyone else has any way to confirm this. But i work in a repair shop and see a LOT of phones and consoles. And with switches I've noticed if the m92 has gone bad it is also draining the battery and killing it this is likely do to chargers that aren't the original. Iphones do...
  5. P

    Hardware Is it still possible to hack?

    Id say so, not sure why it wouldn't unless someone else knows why it wouldn't. Doing a full mb swap contains all the original important bits... just install TRG and run Hekate. Either way once you put switch into rcm TRG will tell you.
  6. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    Soo I have an update as of now hahah, i took off the speaker input and checked the lines, immaculate. I was like there is no way! I restarted my thermal cam...... it was uncalibrated! The BQ is what is getting getting white hot, but can that cause switch to get stuck at loading screen? Also, I...
  7. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    So I havnt taken of wifi chip, but it still gets super hot in that area i showed, seems heat is coming from back of board. Also, when screen is sitting at logo, if I force a shutdown with power button, it creates a pop noise, which I thought was interesting. I'm trying to figure out what's on...
  8. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    I actually just gave it an IPA bath with toothbrush, ill go for it again. auto @Hologram Quick Question while we wait, do you know if the console will fully boot without wifi chip on the board? If it does, I could always remove my wifi chip and see what happens, I have some preballed ones on...
  9. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    I hope this is good, my cam quality isn't too great.
  10. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    No liquid damage, console just stuck at logo, pulls good amps, seems to fast charge, line 5 and 6 on m92 are good, pulls 5v on cap next to bq, fuse infront of port is good, no shorts on back near p13. Any idea on how to test those components on the back leg there in the video? I have no...
  11. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    The cap all the way to the left isnt shorted after reflowing the chip, but the other 2 still beep. But now I've taken a closer look under cam and those components aren't getting hot, this area is. I seemed to have scraped it, but i don't understand how it'd create a short Does anyone have any...
  12. P

    Check the thread I just created, might be worth checking bq. And I'm going check those voltages...

    Check the thread I just created, might be worth checking bq. And I'm going check those voltages right now for you
  13. P

    Hardware Stuck in boot logo, m92 and bq replaced, wifi chip reflowed

    Hello! So as the title says I have a switch stuck on logo. I've tested m92 and replaced It twice, no shorts on it or p13. Getting good values from them as well. I replaced charger port, it's working perfect as well. I replaced bq from donor board, and also reflowed wifi chip. Still nothing past...
  14. P

    Hardware Switch stuck in boot logo

    I changed out m92 twice, and still nothing! I have ordered some wifi chips, preballed and hopefully will get them tomorrow or saturday. I have those 2 caps, i was hoping they would be missing when i looked at the switch ahah!
  15. P

    Hardware Switch stuck in boot logo

    I am having the same issue, I replaced m92 and bq, and its charging and all values are great no shorts. Switch boots and tunrs on but stops at 2nd logo, I can't enter recovery mode either. I tried reflowing the wifi chip but it didn't work. Really hope we can figure this out. Be sure to tag me...
  16. P

    Hardware M92 line 6 0v, 1 short and pulling .46 no power

    Switch is working 100% now, needed to reflow the lcd connector, and run a jumper for the pad that was burnt, works like a charm. Never realized so many issues could be cause by that connector. Thank you Everyone! If anyone is having same symptoms I did, do the normal and check the fuse infront...
  17. P

    Hardware M92 line 6 0v, 1 short and pulling .46 no power

    Sooooo, it turns out my amp reader was reading very wrong, tried new reader with same cable and its opulling 1.84, both joycons work after reseating but the switch doesnt disply unless docked, is this just an lcd issue or something more?
  18. P

    Hardware M92 line 6 0v, 1 short and pulling .46 no power

    I soldered new connector on, the old digi and lcd I'm trying to use is VERY BAD, and slightly torn. when docked it shows up, it is touching but I'm sure the lcd is dead. It only pulls .46 then goes to .09 no shorts on p13 but m92 pin 6 is pulling 12v with charger and pin 5 is pulling 12.4. This...
  19. P

    Hardware M92 line 6 0v, 1 short and pulling .46 no power

    A2 an a3 is beeping on continuity. The one you have removed is beeping as well. The connector is removed as well. The pads don't seem to be missing but a few of them burnt it seem
  20. P

    Hardware M92 line 6 0v, 1 short and pulling .46 no power

    Ohhh my. So i was able to unbend those pins, one broke, of course. I have a donor board. and all of those shorts disappeared, even the bottom cap beneath the m92 and the ones on the back, now there is something shorted to the left of the fpc connector, not sure if its supposed to be. they look...
General chit-chat
Help Users
  • No one is chatting at the moment.
    bassviolet @ bassviolet: wth