Search results

  1. CHTechRepair

    Hardware Vconn input to M92T36 Explanation

    MAX77620 regulates the 1.8v rail. Output can be measured on one of the large inductors beside the IC. It also outputs many other 1.xv rails. Can be a bad coil, or bad MAX77620.
  2. CHTechRepair

    Hardware My switch doesn't charge, won't turn on, or is otherwise not functioning at all. Where do I start?

    I personally have never had to troubleshoot any 5v rail aside from DC-IN. It would require boosting since the battery voltage is always below 5v, which leads me to believe it wouldn't be required to start the device as everything logic based is 3.3v or lower. I'm also not familiar with any rail...
  3. CHTechRepair

    Hardware My switch doesn't charge, won't turn on, or is otherwise not functioning at all. Where do I start?

    Good work! This is why it always helps to test around an IC before you go to replace it, sometimes components around it really are the problem you just never know! Based on this info I wonder if the 3.3v rail actually comes from a transistor above M92 or in that area above Audio IC? Strange...
  4. CHTechRepair

    Hardware Vconn input to M92T36 Explanation

    You will likely need a donor to figure this out without just blindly replacing components. If your battery is charging but the console has no power I wrote up a thing about what I look at in these situations here. MAXX77620 is the most likely candidate if there is no other visible or measurable...
  5. CHTechRepair

    Hardware Broken Switch - Won't turn ON, but it charges

    The shorts you are measuring on MAXX77621 aren't likely true shorts. I've gone over this a lot those rails are very low voltage and therefore very low impedance. A diode mode measurement can confirm a true short here. Follow my guide's solution #1 for tips on where to go when you have battery...
  6. CHTechRepair

    Hardware My switch doesn't charge, won't turn on, or is otherwise not functioning at all. Where do I start?

    I'm fairly sure the 3.3v logic/IO rail is switched by MAXX77620. Take a diode mode measurement above P13USB there's a large capacitor on this rail. Red probe on ground, black probe on 3.3v side of capacitor. You want above .300 here, less is going to be a partial short more than likely. Since...
  7. CHTechRepair

    Hardware My switch doesn't charge, won't turn on, or is otherwise not functioning at all. Where do I start?

    Will do, wrote this up on my phone let me get that sorted. Edit: Done, thanks so much for the feedback!
  8. CHTechRepair

    Hardware My switch doesn't charge, won't turn on, or is otherwise not functioning at all. Where do I start?

    I haven't seen a guide for where to begin if the console has no power at all. I'm writing this as if a Switch is in front of me and I'm looking at it for the first time. Typically the only switches I don't fix are severely liquid damaged ones or CPU/GPU failure as they take too much effort...
  9. CHTechRepair

    Hardware Extensive Trace Repair on Charging Port

    This one is just a normal Amscope binocular scope off Amazon. I just use the 0.5x lens that comes with it nothing special. I also use an Eakins trinocular scope I bought from China, same deal no fancy lenses but I use a more powerful light since you lose some to the third viewport.
  10. CHTechRepair

    Hardware Extensive Trace Repair on Charging Port

    This was a really fun challenge. This port looked just fine on the outside, the device showed all signs of M92 failure. Turns out damn near every pad for the top layer of pins had been torn away including DC-IN traces. Anyway I decided to rebuild it and figured I'd share how this was achieved. A...
  11. CHTechRepair

    Hardware Replace Switch AC Adapter cable

    This is 100% true the switch actually complains about AC input if it's asked to put display port out under 15v.
  12. CHTechRepair

    Hardware Switch cannot boot past Hekate after replacing fan

    Format the card itself or put another card with just OS and see if the behavior changes. I get this behavior sometimes and formatting my card has brought me back from it in the past when flashing eMMC with a backup did not. The card is being read since Hekate is booting from it, I'm thinking...
  13. CHTechRepair

    Hardware Replace Switch AC Adapter cable

    I will get back to you shortly
  14. CHTechRepair

    Hardware Switch cannot boot past Hekate after replacing fan

    Sounds like your SD card was being read as your device was being disassembled. I use SX OS but same story minor SD issues cause the console to hang after the Nintendo logo on any firmware. It's always stressful taking the card out for me I've done it a few times to myself. Make a backup and...
  15. CHTechRepair

    Hardware Replace Switch AC Adapter cable

    Just wanted to show this is valid. A switch can and will negotiate 9V charging properly I would assume from any quality USB-C power supply device. This photo is showing not a 20v Apple Macbook USB-C PSU but an 18W USB-C Apple Lightning block. Moral of the story: good design is good design don't...
  16. CHTechRepair

    Hardware Replace Switch AC Adapter cable

    I'll post a pic of one on 9V if I can, off til Friday. Maybe I'm just imagining the voltage from doing too many iPhones, but I know they will nego with Macbook blocks no issues not 5v. Those blocks are supposed to only do 5v, 9v, 20v. I have no idea of the technical specs of M92, just what my...
  17. CHTechRepair

    Hardware Nintendo Switch heat sink problem

    They could be stripped, though I've never seen it personally. I would take the board out and see if you can drive the screws without the board in the way. Any small bow is going to misalign the screws and make it very difficult if not impossible to get them in. There isn't really another good...
  18. CHTechRepair

    Hardware Replace Switch AC Adapter cable

    You should be completely fine wiring another end to this cable, nothing is special about the switch the voltage in is on the same pins and data is carried on the same pins. I do a lot of work on Macbooks, which nowadays use 20v USB-C. Turns out their PSUs can negotiate 9v too for iPads and...
  19. CHTechRepair

    Hardware Nintendo Switch heat sink problem

    This isn't sounding good. Reflowing these GPUs isn't something you really want to do. Reballing is preferred entirely as reflowing if it does work will not be reliable. This isn't something you can do with even intermediate level tools. You need preheaters, a careful approach, a stencil, the...
  20. CHTechRepair

    Hardware slightly bent screen , purple spot . some questions.

    If you think the device was exposed to moisture I would open and clean it first before liquid damage becomes an issue. Aside from that yes the LCD can be replaced and will take any spots you see away. If you aren't used to working on modern electronics with adhered digitizers maybe get yourself...
General chit-chat
Help Users
    Xdqwerty @ Xdqwerty: @SylverReZ, @Psionic Roshambo sorry but im not that used to listening to non game music +1