Search results

  1. Denis_Lissov

    Hardware Xbox One X - BGA piece NFD740, please help me to find it !

    Nice work Sir. Would do it myself, but got no faulty Xbox here. Cant wait for your results.
  2. Denis_Lissov

    Hardware Switch no picture in hanheld mode

    If everything was working before the only thing I can imaging is bending some pins of the LCD connector. Happened to me 2 after that I started putting the LCD cable into connector before putting the board in the case. I had bended switches with the APU no making good contact with the board. The...
  3. Denis_Lissov

    Hardware Switch no backlight and cracked chip

    Check for resistance on the 1,8V 1,3V lines. They can be found around max77620 ic
  4. Denis_Lissov

    Hardware Switch help

    If the switch works fine and only gets hot. I would check if the fan is spinning or damanged. Sometimes I cant tell the fan is spinning because it is so quite. In this case I take a little paperstrip and push it through the radiator until I hear a noise from the fan hitting the paperstrip. To...
  5. Denis_Lissov

    Hardware switch only charging at 0.43 amps help needed thanks

    There is no need for continuity on USB dataline to start the switch. But there is a good possibility that that switch is in auto rcm. I had quite some switches with broken Port and bad M92t36 that where used in auto rcm. Some of them were banned. So check the usbline filter for continuity and...
  6. Denis_Lissov

    Hardware Switch Won't turn but boots in Hekate

    Maybe it is not a solution for your problem, but I had a board yesterday with 0,4 V in diode mode but only on one dataline. It was the ESD component for the USB data lines.
  7. Denis_Lissov

    Hardware WiFi error 2110-1115

    @ppzikos Are you able to change the Wifi IC with a new one. According to this thread(Debugging faulty BCM4356 / orange screen / boot loop | Page 8 | GBAtemp.net - The Independent Video Game Community) programming is needed or you use one of a donor board?
  8. Denis_Lissov

    Hacking RELEASE Lockpick_RCM payload - Official Thread

    that's what I didn't want to do because I am scared to screw something up and getting the switch banned. But as you said that's the way to go. Thank you, guys.
  9. Denis_Lissov

    Hacking RELEASE Lockpick_RCM payload - Official Thread

    Thank you for your response sir. But I was thinking the keys are saved in the console? And the shutting down of the console is normal as well because there no new keys contained? Or the firmware doesn't contain any masterkeys? I think I am misreading your answer. Best regards
  10. Denis_Lissov

    Hacking RELEASE Lockpick_RCM payload - Official Thread

    Hello friends, today I tried to dump the keys. FW 12.0.2. As mentioned before if I don't have the sept folder I am able to dump the keys, but not all the keys. It says the sept folder is missing if I remember correctly. If I put the folder in the right place the console shuts off with the...
  11. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Hello guys, thank you for your support, but I decided to let it be for now. I sadly have no time to continue, but will try to fix the third board that is missing components. Best regards
  12. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    So no luck so far still unable to init emmc. Maybe someone has another suggestion? The screen works fine tested it today as well. I have a third emmc here and if I put it into the bricked switch. It shows a picture but stuck at the logo. So from my inexperienced view, it's an emmc issue...
  13. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Got it sir. Will report back on tuesday.
  14. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Never did of this before so just asking. I have a 8gb SD card here is it enough? else I have to order one. I was only able to use hekate with emmc on unpatched second switch. So the unpatched switch doesn't allow to connect to the internet or the patched switch where I have the emmc from...
  15. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    So I am able to inject but when I select autorcm it says failed to init eMMC. At the beginning it says: Failed to mount SD! Missing LP0<sleep mode> lib! Missing or old Minerva lib! Update bootloader folder! Press any key... And I have a warning: Nyx is missing! I don't have SD I do not know...
  16. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Thanks a lot for this information. Will print the jig and report back. Following this instruction to enter the rcm mode. Forgot I cant post links
  17. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Hello, I am not sure what you mean by rcm device. Do you mean a working switch?
  18. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Thank you for your respond. Just tried it nothing happens. It is just like before Nintendo draws 200mA from the battery and no signs of a picture.
  19. Denis_Lissov

    Hacking Nintendo Switch autorcm no picture at all

    Hello guys, I am new to the forum so bear with me. I bought a Nintendo Switch for parts of ebay to repair it. I am more about hardware problems, but at this point it seems to me it is more of a software problem. If you plug in 5V USB-C Cable the switch draws 0,45A. If I try to start nothing...
General chit-chat
Help Users
  • No one is chatting at the moment.
    Psionic Roshambo @ Psionic Roshambo: https://www.youtube.com/@legolambs