Search results

  1. ewabc886

    Hardware People with special edition Pro Controllers, I need your help with colors.

    Body: #2D2D2D Button: #E6E6E6 Grip L: #464646 Grip R: #FFFFFF
  2. ewabc886

    Hardware [Question] V1 Type-C port installed with jump wires

    Thank you for the recommendation, but I found that it's not feasible in my case. First is its price, second is that I don't really need a "normal" Nintendo Switch. Anyways, I would like to know if the jump wires matter in the case. I had all points' continuous tests passed but the type C port...
  3. ewabc886

    Hardware [Question] V1 Type-C port installed with jump wires

    This board came from someone tried but failed to swap the type C port. Instead, he ripped off some soldering pads on the board. As seen in attached photo "TypeC_Trace", result of me trying to repair the broken trace by both jump wires(too thin?) and repairing pads(too thin in another way?)...
  4. ewabc886

    Hardware Joycon pin 5 stays high

    To be precise, I replaced the connector at the upper left corner in the figure. 1693972623 I also found that normal diode voltage from pin 5 to pin 6 should be 1.8V, same as the high state voltage. But the malfunction board has diode voltage of 0V 1693990124 After a few hours of checking, it’s...
  5. ewabc886

    Hardware Joycon pin 5 stays high

    I have a joycon having pin5 staying at high when it's plugged into the switch. I need to manually short it to ground to bring it to low, then the switch sounds "click", and the wired connection is done. Once the joycon is disconnected, it goes to wireless mode. When it's connected back, pin5...
  6. ewabc886

    ROM Hack RELEASE Overcooked 2 60 FPS mod

    for all you can eat or oc2 just use ReverseNX to force handheld mode, i.e. 720p with overclocked cpu and gpu but make sure that your swich console can also handle the heat from overclocking i feel like almost 70% of time, the switch can handle 60fps at 720p with overclocking but in the end, i...
  7. ewabc886

    Init eMMC Failed, no NAND backups

    In case someone like me uses file base emunand instead of partition method emuMMC. We have our emummc system broken by 14.0+ in file 00 which should be located somewhere like sd root/ emummc/HPE0/eMMC/00 alongside files 01, BOOT0, BOOT1 this cannot be mounted by Hekate through the USB method...
  8. ewabc886

    Tutorial NAND Rebuilding (for no backup / broken eMMC)

    Which step were you at exactly? Step 12 is quite long. It seems that your eMMC GPP isn't correctly connected to computer Have you use a Hekate payload injected directly from PC? Hekate loaded by chain loader may not work
  9. ewabc886

    Hacking Question Will the OLED Switch be SX-Core compatible?

    not slightly different already lol the board has different in most parts. Only similar internal parts are the fan, battery, and the part of the board under battery.
  10. ewabc886

    Injecting Payloads just gives black screen.

    "Smashed the stack with a 0x0000 byte SETUP request!" An ipatched unit will give this "0x0000" thing RCM mode activated =/= hackable an unpatched unit will give "0x7000" in this line if i remember correctly. So it's a V1 patched Switch
  11. ewabc886

    Hardware Components used on the Switch (mostly the motherboard and main console)

    Thanks for the infor and the confirmation. So the resistor I'm looking for should be 0201 150Ohm?
  12. ewabc886

    Hardware Components used on the Switch (mostly the motherboard and main console)

    That's interesting to see a 0Ohm
  13. ewabc886

    Hardware Components used on the Switch (mostly the motherboard and main console)

    Hello, I would like to know the resistor value pointed by light blue arrow in the picture (Fig.1). The board I'm dealing with is really messed up by the last owner at the same resistor (Fig.2). I guess he was trying to solder the trinket M0 It booted OFW normally, and cannot boot into CFW due to...
  14. ewabc886

    Hacking Question Will the OLED Switch be SX-Core compatible?

    It seems that Nintendo doesn't really care as long as it's a modchip version. They only block the softmod is enough Then just sue anyone who produce the modchip. lol
  15. ewabc886

    Hardware Switch touch only working in certain spots on the digitizer

    Thanks again for the information. That helps a lot so I don't need to test the gamecard boards in hand one by one
  16. ewabc886

    Hardware Switch touch only working in certain spots on the digitizer

    Hello, Thanks for the information. May I ask if it is possible for you to photo the gamecard board? Like the photos in this post, it seems that we can tell if the board matches with the version of digitizer by looking at the gamecard board. Thank you.
  17. ewabc886

    Hardware [Question] Stuck Switch Logo evolve to no backlight, no image

    I don't know if i'm getting your idea correctly. Does it mean that it's possible to have a faulty USBC port causing a boot problem, which can't even bright up the LCD and backlight? If it can be, it's quite dangerous for the port. Like the test for capacitors, we can look for a grounded side...
  18. ewabc886

    Hardware [Question] Stuck Switch Logo evolve to no backlight, no image

    I'm sure, all checked, and with flashlight
  19. ewabc886

    Hardware [Question] Stuck Switch Logo evolve to no backlight, no image

    But both backlight and LCD are off all the time, so not very possible.
  20. ewabc886

    Hardware [Question] Stuck Switch Logo evolve to no backlight, no image

    Yes I tried I can still detect the RCM mode and seems successfully injected payload. But no clue on why isn't there image and backlight at all Recently cant's get more test.M Maybe need to come back to it after a month or so.
General chit-chat
Help Users
    OctoAori20 @ OctoAori20: Nice nice-