Search results

  1. M

    Best way to install NSPs?

    Any idea how to enable 3.0? I tried usbc to usbc but it only show 2.0. My Atmosphere config looks like this. [usb] ; Enable USB 3.0 superspeed for homebrew ; 0 = USB 3.0 support is system default (usually disabled), 1 = USB 3.0 support is enabled. usb30_force_enabled = u8!0x1
  2. M

    Trustworthy HWFLY installer needed

    Hi all, Im looking for a trustworthy HWFLY installer. I was skinned by a member here for $830 for a premod and an install on my current console. Moved on. Now im looking for an installer for 2 oleds, both with the HWFLY v4.1 chip. Please reach out. Thanks,
  3. M

    Nintendo Switch OLED - help with component

    Anyone know the value of this SMD resistor?
  4. M

    Hardware Repair specialist?

    Hi, Do we have a resident repair specialist? My repairs are beyond my experience and im willing to pay a professional to clean my 2, now broken switches up. Any info would be helpful. Thanks
  5. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    I think i need to go from the legs of the USB C port to the ports on the back no? Which legs on the USBC are D+ and D-?
  6. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Looks like the SD port on the board had a loose pin. I desoldered the pad and I'm waiting on the new one to arrive tomorrow.
  7. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Got home and the Switch just started working again, same as the Mexico trip. So bizarre.
  8. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Hi all, When booting into Atmosphere via RCM I get the, "failed to mount Emmc" error. When I boot directly into official FW the console boots no problem. I have a Trinket M0 installed and its been fine for a 2 years now. This happened when I went to Mexico but then resolved on its own and now...
  9. M

    Hacking Switch with AutoRCM won't accept payload

    Interestingly my Trinket M0 just stopped injecting the payload. Switch goes in to RCM mode then I have to manually inject with the TegraRCMgui. Not sure what could have happened, was working fine for a year or so.
  10. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Yup, so now i just need the point on the front.
  11. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Yea I lifted those, so now I need to solder a bridge between the chip above those pads then to the rear of the PCB. I need all 4 of the points... I think its the two middle pins above on the 6 pin chip above the lifted pads, and I'm not sure of the 2 locations on rear. This was my original...
  12. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Hi all, I lifted the two pads data pads D+ and D- during a trinket install, does anyone know how to create a bridge? I know there was a diagram but I cant find it anywhere on here. Thanks,
  13. M

    Hacking Console not entering RCM

    Hi all, long story short i broke the LCD connector on a switch, so the screen is dead. It also had the right joycon not detected in handheld mode which i fixed by replacing the rail. Now it detects the joycon. Issue is; it's not entering RCM with a printed jig I purchased on Amazon. I have...
  14. M

    Hacking Switch not booting past the Nintendo logo

    Sorry for not updating. Fat32, had to reformat to exfat. thanks
  15. M

    Hacking Trinket M0 install troublea

    Hi, my response was to Harmony United. lol.
  16. M

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    Post pics of the install.
  17. M

    Hacking Question SX OS (2.9.3) cfw won't boot after upgrading to 9.0.1

    Exfat format issue. You need to reformat the card unfortunate.
  18. M

    Hacking Trinket M0 install troublea

    Sounds like you're not in RCM mode to me. Can you post the solder job for the RCM strap. Actually, post pics for all straps. You could have shorted the wrong pins for the RCM strap.
  19. M

    Hardware Solder Battery to board

    So i soldered to a + pad and a - pad and then combined both red wires to the + and both black top the - from the battery. Then I soldered the gray to a pad the trace led to. I'm having no issues. This was the culprit that making me pull my hair out of my head. I could not consistently boot the...
  20. M

    Hardware Solder Battery to board

    I was able to use the pads under the connector. Thanks.