Search results

  1. LameNobody

    Hardware [Question] Superglue And PCBs

    It would work fine, however, super glue may not be the best option for strength with such a low surface area. You could go with epoxy or some sort of cement type of adhesive... Instead of just securing the bottom of the microUSB connector to the board, i don't see why you wouldn't do the whole...
  2. LameNobody

    Hardware New 3DS ribbon cable / pull sockets for home button, mic, nfc

    The two bottom connectors are home button, and microphone. the one near the circle pad should be bottom LCD backlight, and the one near the left side of the board is probably nfc.
  3. LameNobody

    Hardware New 3DS ribbon cable / pull sockets for home button, mic, nfc

    I say this a lot in the hardware section because it's a common thing... so, here's a quote from me.
  4. LameNobody

    Hardware 3ds Powerbank

    Sounds like its probably a powerbank issue. Using a usb tester, the 3ds only draws around 400mAh-470mAh when charging. Lots of powerbanks turn off when they detect little load. Your powerbank may turn off when there's less than a certain amount of power being used. Try different power banks...
  5. LameNobody

    Hardware Circle pad lock down lever thingy.......

    So, somewhat of a hack suggestion... Hot glue. (I've done this on more than one console, they're both still fine.) You're not repairing the connector with it, you're using it to secure the cable connection. Place the FFC in the cable slot and align it where it needs to be. Take a smallish drop...
  6. LameNobody

    Hardware N3DS XL POWER ISSUE. HELP!

    ^^this The battery may not be damaged, but i know mine had voltage but would not take a charge even with the new board I was able to charge the battery with a generic lipo charger, i still needed to replace the battery
  7. LameNobody

    Hardware N3DS XL POWER ISSUE. HELP!

    Likely damaged charging chip, which is why it needs the power cable plugged in. and possibly shorted the battery
  8. LameNobody

    Hardware N3DS XL POWER ISSUE. HELP!

    did you connect the battery to the 3ds while dis-assembled? Odds are you connected the battery wrong, even if just for a second I have done this. I fixed it with a new battery and a new ABXY button board. This board contains some charging circuitry which was most likely damaged when the...
  9. LameNobody

    Hardware Are there any new 3ds xl headphone jack spare parts?

    That should be for the home button
  10. LameNobody

    Hardware did I turn it into a paperweight?

    Nobody mentioned that the n3ds charging daughterboard could be fried? That's pretty common with shorts on the n3ds xl, the board that has the A B X Y buttons, a lot cheaper to replace too.
  11. LameNobody

    Hardware What these pins on the game Slot are supposed to do?

    These two pins are spring contacts that get pushed together when a cart is inserted. It allows the ds to detect if there is a cart in the slot Cart in slot = pins connected to eachother empty slot = pins not connected to anything Honestly, just solder the two pads together since you broke the...
  12. LameNobody

    Tutorial Tutorial for 3000mah battery mod for PSP 2000 & 3000

    There are three pins on that samsung battery, but i only used the pos and neg pins. I wired it directly to the psp cell within it's battery, so it should use the protection circuitry of the psp battery/psp
  13. LameNobody

    Tutorial Tutorial for 3000mah battery mod for PSP 2000 & 3000

    I did this a couple months ago with my $10 psp, i was told the umd reader was broken... so i pulled it out and decided to shove a battery in.. I know it being held in with hot glue looks awful, but i didn't care enough to remove the UMD door and glue it properly and i used 2.5mm headers and...
  14. LameNobody

    Tutorial How to UNBRICK your N3dsXL with NO SysNAND Backup File With B9S (Sighax) and Hardmod

    Hey @gamesquest1 , I have a system that has been flashed with the nand from another console and has no backup of its original nand... Do you think this method would do anything, or am I in need of another solution?
  15. LameNobody

    Hacking [Motherboard] I lost a small part :(

    I've had luck with hot glue, Put a small drop on the ribbon cable, wait two seconds, then press on the glue. Pressing on the glue pushes the ribbon against the pins and spreads the glue at the same time, it hardens pretty quickly and can easily be removed with rubbing alcohol
  16. LameNobody

    Hacking Recompiling PRX (GTA remastered)

    Well, updated my post with V2 without the X/R swap, enjoy.
  17. LameNobody

    Hacking modifying virgin 2DS with B9S

    here you go https://mkey.salthax.org/
  18. LameNobody

    Hacking EZ-Flat IV 2.01 - An EZ-Flash IV 2.01 skin

    I'll test it now, if you can't. Glad to see this theme is being ported to the latest release
  19. LameNobody

    PS1/2 Buying a modbo 5.0

    try looking up some button combos to try, if he put a modbo in there already, you could press triangle and circle while booting and see if you get a config menu And, buying from EurAsia is a great option, modrobert is a great guy it seems
  20. LameNobody

    Hacking Recompiling PRX (GTA remastered)

    The Fl0w released V2 of this plugin fixing the inverted camera bug, you can now change your camera movement in the game's settings. However, the buttons are still swapped... So, I removed the code that swapped the buttons and here it is: V2 of the plugin without the X / R button swap...
General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: Wut @Xdqwerty didn't say good night +2