Recent content by Zm1231

  1. Z

    Bricked wii w Boot 2 Installed

    You mentioned that you cannot sync your controllers. I almost guarantee your Bluetooth/ Wi-Fi module has failed. If that module goes bad your Wii will no longer boot properly. Doesn't matter if your nand is working or not, it just will not boot boot mii will work but it doesn't matter what nand...
  2. Z

    Atmosphere CFW updated to pre-release v1.8.0, adds support for firmware 19.0.0

    Geohot didn't exactly sell out. He released the PS3's keys and then Sony took him to court and he was more than likely to lose and the courts stated that there can be a a "forbidden numbers" he took a settlement so he wouldn't have ended up in jail because they had some serious charges against...
  3. Z

    OLED with Instinct NX Switch

    It won't seem to boot just freezes and never loads the recovery on first setup. But it seems like the SDLOADER is an older one the one I have is this one in the botom right it says I have R0.31 H1.0 Ive seen newer ones have this one if I try to boot Lakka I get this: If I try to boot...
  4. Z

    OLED with Instinct NX Switch

    I recently had a Instinct NX (Black Mother Board Rocket NO SD Screen) installed in my OLED Switch I got a 1 TB SD Card for it and have everything setup with my firmware however I'm trying to get Android and Lakka to boot however it seems this wont boot. for lakka I have the latest version and...
  5. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    So I was able to get the switch reassembled without the picofly installed but it still does not power up. I do not see any bridged solder connections anywhere everything looks right. The cap that was knocked off was reinstalled. Pressing the power button result in no activity no fans spin up
  6. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    @abal1000x that's what I saw but we already had the USB port and everything desoldered off the pico before that firmware came out. We can attempt to add it back on to update but the issue is right now even without the Pico installed in the switch it doesn't look like it boots so hopefully...
  7. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    I haven't tried I'll take the doc with me to the shop when I go to pick it up tomorrow and see if it outputs video if so it could be a damaged cable.
  8. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    Once I pick up the switch tomorrow I can describe more of what's happening and then get photos of the board to post. I took it to a chain shop here that does micro soldering and cell phone repairs they replace BGA and do all kinds of other things but it seems something got messed up but we're...
  9. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yea trying to figure out what may be wrong. I'm picking the switch up tomorrow from the shop. as of right now the wiring is still in place I asked the installer to remove the Pico and flex cable for now but leave the wiring and I can work on it from there. I just need to get it working again so...
  10. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    Where is the EN IC Located it looks like it would be next to the 3.3v Source When I compare it to the OLED Board layout but the IC there doesn't have EN on it. Is this the 7780 IC next to the 3.3v on the OLED? I was able to check it and don't have a short here but the switch doesn't boot up.
  11. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    We disconnected the 3.3v and GND to cut the chip off to see if it would boot normal but it didnt. We also completely remove the Pico and flex cable but the switch doesn't seem to indicate any activity at all so something is messed up. if we put the chip is put back in its will just go go blue...
  12. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    ok looks like it doesn't boot with the 3.3v and GND Connected from the Pico so looks like something may have been damaged maybe a cap was popped during the install not entirely sure what to look for. The only thing I know they did while performing the install but corrected was the CMD point...
  13. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    I was thinking I might possibly have a bad flex cable but we where testing to make sure the board wasn't messed up shouldn't removing power and gnd form the pico (Basically powering it off) allow the switch to boot unmodified. Would anyone happen to know the correct diode values of each of the...
  14. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    So I have an oled and picofly with a oled flex cable at the time 2.67 was the firmware available and was flashed I took it to a shop to have it installed they where able to get the picofly installed and have the cpu connected to the 3-4 pins on the flex cable but it seems to boot blue then cyan...
  15. Z

    Hacking Hardware Picofly - a HWFLY switch modchip

    So I found what looks like a Pico custom board on Aliexpress that comes with the OLED Cable and a new Mainboard cable. Has anyone tried this yet?
See more