Recent content by Werner434

  1. W

    HWFly / Picofly - Work clean when cutting CPU- and EMMC-Frames

    Good evening. To separate the CPU frame and the EMMC frame, many technicians use an electronics clipper like Knipex 7861140 or Sunshine SS-109. However, the material of the frames is so soft that it is less of a cut that you make. It's more of a squeak. And this is what the result usually...
  2. W

    Component missing on Switch Oled?

    Hello folks, is there a component missing? My Switch do not turn on. Display remains black. Thank you....
  3. W

    Switch Oled with HWFly, install and start Ubunto (Problem)

    Got it solved. I updated the SD Loader. Now it's working.
  4. W

    Switch Oled with HWFly, install and start Ubunto (Problem)

    Good evening friends, after the installation I get this error message when I start it for the first time. What can I do? I habe a Switch Oled with emmc brand Sk Hynix und with HWFly 4.2. Until now the original firmware the chip comes with is installed. It's the firmware that says "No SD Card"...
  5. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    The two capacitors look fine at my oled. Stand in line.
  6. W

    No wifi after hwfly.

    Did the WiFi stop working at all? Or were there problems with the Wifi operation when you use the console? In my case, all Wifi´s are displayed reliably, but I cannot connect to my WLAN. I keep getting error messages when trying to connect.
  7. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    I just swapped the antenna at the top right for one with a intact connection cable and: It doesn't work either. What can I do?
  8. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    yes! WLAN worked well after the mod. What I just noticed is that the sheathing of the connection cable for the WLAN antenna at the top right is slightly damaged in one place. The lines are undamaged, only the sheathing.
  9. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    But it happened at OFW and CFW at the same time. And I noticed that joycons work very well on the Switch, wirelessly not working well: 1. Are not synchronized for wireless when physically connected to the switch 2. difficult to synchronize (you get it right after several attempts) 3. Despite...
  10. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    yes, with "s" starting. 1681076195 Everything seems to be going fine. But I noticed that recently the wifi stopped working. The switch reliably finds the various WLAN networks and also notices changes, but cannot connect. Neither with my normal WLAN, nor guest access and also not via iPhone via...
  11. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    It is about this statement from one of the professionals, also pointing out that there may be other opinions: "I no longer reflow the DAT0 connection because, statistically and on average, it only lasts three months. Different solder-tin materials an compositions an the internal heat from the...
  12. W

    Nintendo Switch consoles with HWFly - later problems caused by the heat generated by the consoles?

    Hey guys, I did my first conversion yesterday. It worked well. I'll do one thing differently next time, but that's just a detail. In order to avoid a possible undesirable development, I am now concerned with the question of whether problems can later occur in the various work areas for the...
  13. W

    Switch OLed mit HWFly welche Version

    Yesterday I did the conversion with HWFly 4.2, for lack of an alternative with enamelled copper wire 0.1mm. I don't like the wire. Works great, but the insulation is very thin. Who knows if something might have ripped open somewhere. I'm waiting for my 36AWG UL10064 PTFE wire. I will probably...
  14. W

    Switch OLed mit HWFly welche Version

    16.0.1 for HWFly 4.2 or HWFly 5 is ok? Now i have 14.1.1 oder the oled....
  15. W

    Where can i download the files for Micro-SD-Card for Switch Erista1? (to Install Hekate/Atmosphere)

    not here at the forum?
See more