Recent content by Swarmx

  1. Swarmx

    Trinket M0 won’t let me transfer files to it again

    ribbon cables work fine, just dont know which pin is used from the vol down so it becomes hard to track down
  2. Swarmx

    Trinket M0 won’t let me transfer files to it again

    have had a try to look around and havent managed to find anything at all is a pain when all i need a working vol down and its perfect
  3. Swarmx

    Trinket M0 won’t let me transfer files to it again

    to be honest i probably did but i noticed it now i guess but i think its fine im just being a bit paranoid i assume because ive seen some forums for battery life on trinket switch haha. Do you know where i can get the schematics for the nintendo switch power button/ vol down button so i can see...
  4. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Yes, now it’s just the volume down and battery drain xD, this isn’t going well haha
  5. Swarmx

    Trinket M0 won’t let me transfer files to it again

    OK sorry for the late reply i had been working on it all day so what happened got everything working, just volume down is fixed, the vol plus issue happened with the resistor and the clip was also faulty for the ribbon so both were replaced and worked perfectly just the volume down needs to be...
  6. Swarmx

    Trinket M0 won’t let me transfer files to it again

    hey so i got the vol up working and power etc now just the vol down doesnt wanna work do you know what controls this? or what i can do to fix this update: switch boots both ofw and cfw although cannot seem to located payload.bin on root of sd card so i have to manually inject with pc
  7. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Ordered a new trinket, honestly had enough of this one. Any tips for the new one?
  8. Swarmx

    Trinket M0 won’t let me transfer files to it again

    I got the files from guide, and used them but now it won’t let me flash any uf2 files to it at all which is quite annoying. Will try the auto rcm and hopefully that works to send the payload. Volume button is working now after replacing the resistor with a small bit of kynar wiring works...
  9. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Doesn’t look the best but that’s the point 3 or the rcm strap. And even with this attached to point 3 it still doesn’t like to boot into rcm just straight into ofw
  10. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Thats fine thank you very much anyway i really appreciate it anyway. i will try see if i can reflash it tomorrow and will let you know
  11. Swarmx

    Trinket M0 won’t let me transfer files to it again

    I will have to reinstall but I’m 99% sure my wiring is fine I have bridged the 2 pads and everything is short and clean. As I used to do hard mods on xbox 360s for a long long time. So soldering skills are okay. I am going to replace the resistor, and will update you with the function...
  12. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Yes I managed to install cfw before and it worked like a dream. I uninstalled the chip. To check the switch was working but this is where I noticed the volume strap wasn’t working up all other functions still worked. I think the connector isn’t holding the cable down strong enough so maybe not...
  13. Swarmx

    Trinket M0 won’t let me transfer files to it again

    I t I think I have buggered my volume button as can’t change the volume now. Can show pics of resistor so if needed. Trinket leds either flash from purple to red and stay red while it boots ofw. And that’s all it does. I have the payload on the root of the sd card plugged in. Not sure if it’s...
  14. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Oh yeah with everything soldered, in all the correct positions but it only boots the ofw don’t know if I was missing a step or something
  15. Swarmx

    Trinket M0 won’t let me transfer files to it again

    Yeah, I do reset it every time I want to drag files over. I double press the reset and drag the files over but they refuse to stay on it. And now it’s just gotten worse and won’t even copy and form of uf2 files over
See more