Recent content by snake2

  1. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    Of course not, I waited until I was done like a normal person The test point in between the RAM and WiFi shields Helder had it shared on OSHPark for a little while but I think he took it down
  2. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    My latest install with Helder's expansion board. Using a ground near the USB
  3. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    Run the toolbox from the Hekate payload menu
  4. S

    Solderless modchip options

    Unfortunately there are no solderless mod chips for the Switch. Even the CORE for the v1/v2 require solder a flex cable to the CPU capacitors If you want a solderless solution look into picking up an unpatched v1 and an RCM Loader
  5. S

    Help with switch mod (chipped)

    OK you will want to update it to the latest HWFly firmware, I am not sure if I am allowed to link to it but it is easy to locate with Google After updating I would suggest using the HATS pack, this one I know I am not allowed to link to If you are using emuMMC you will need to use Hekate to...
  6. S

    Help with switch mod (chipped)

    First you'll need to determine if the chip is running the original SX firmware or another type of firmware. Boot up the Switch and post a picture of the no SD card screen
  7. S

    Picofly AIO Thread

    The ones I bought from AliExpress do not show the RP logo in the product image but it is there on the ones that got delivered. It is on the larger IC on the back
  8. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    I had a HWFly Core installed in my Animal Crossing switch and after troubleshooting I found it kept corrupting BOOT0 when writing the payload to the eMMC I pulled the Core out and replaced it with a PicoFly and can reboot to OFW after creating a clean BOOT0 Loving this project
  9. S

    Hacking Hardware Picofly - a HWFLY switch modchip

    How about on the 9001st boot so I can shout "It's over 9000" when I see the smoke?
  10. S

    Picofly AIO Thread

    Updating from 10.x.x to 16.0.1 fixed my BOOT0 after it got corrupted by unlocking On Hekate selecting reboot to OFW gave a black screen but I was able to use Atmosphere to boot stock then update over internet
  11. S

    Hardware Cannot read carts error 2002-2663

    Thanks for this video, I'll give it a try sometime
  12. S

    Hardware Components used on the Switch (mostly the motherboard and main console)

    Anyone able to help me identify these 2 missing components? One is a cap that I don't know the value and the other should be a resistor or ferrite bead This is an unpatched v1
  13. S

    Should OFW boot if just the CPU flex is soldered?

    I cannot get the Switch to enter maintenance mode, the Nintendo logo does not appear when I power on the console. I added an entry for CFW sysNAND and it loads atmosphere in sysNANAD Hekate shows 11 fuses burnt and the eMMC is on 9.0.1 If I hit reboot and select OFW on Hekate then it will not...
  14. S

    Should OFW boot if just the CPU flex is soldered?

    I am troubleshooting a v2 with a CORE mod chip. I can create an emuMMC and boot into the emuMMC without issue. If I try to boot sysNAND or OFW my Switch hangs at a black screen I removed the CORE chip but left the CPU flex on, I disconnected the chip from the flex and connected the eMMC back to...
  15. S

    Hacking TX Announce Preorders for SX CORE and SX LITE

    I asked TX on Twitter and they said the SX Lite does require soldering https://twitter.com/MrPete1985/status/1247837910231105537
See more