Recent content by slimmy182

  1. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    Thanks for checking and for the Scribd reference. I’m already using the EDM-020 service manual as a guide. That capacitor was already inspected under the microscope and cleaned thoroughly with IPA. What you’re seeing in the photo is just light staining, electrically it measures the same as the...
  2. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    from my side I can only say that I did not find obvious shorts or abnormal readings, but without a known-good board for comparison I cannot state with certainty that everything is within spec. What I did verify is: ZQ_A / ZQ_B termination resistors measure ~120 Ω on all banks, including the...
  3. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    Thanks — I checked that. On my board the only net matching that VRefC divider behaviour is the one I measured at ~0.361V in diode mode and ~2.18kΩ to GND, and it’s consistent across multiple RAM banks (bank 5 and a known-good bank on the same board show the same readings). The ZQ resistors...
  4. S

    ps5 EDM-041 - uart 80801101 & 80801601

    it is still working?
  5. S

    Ps5 aurt error 80801101

    did you solve it?
  6. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    Thanks for the input, makes sense. I checked the VPP side already: the 1 µF caps on the opposite side of the DDR are present, in continuity, and diode/resistance readings are consistent across multiple RAM banks, including the failing one. No anomaly there. Same for ZQ_A / ZQ_B: both 120 Ω to...
  7. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    Thanks for the input. I’ve already checked the suspected ZQ termination network in detail: • The two resistors next to each RAM chip measure ~120 Ω to GND (one side 0 Ω, the other ~120 Ω), identical to the same resistors on known-good RAM chips. • Measurements were confirmed...
  8. S

    ps5 EDM-041 - uart 80801101 & 80801601

    Can you please take a look also at my post? Similar problem : https://gbatemp.net/threads/ps5-slim-edm-140-blod-ram-calibration-impedance-error-diagnostics-so-far-error-code-80801510.679366/
  9. S

    Hardware PS5 Slim (EDM-140) – BLOD, RAM calibration / impedance error – diagnostics so far Error code: 80801510

    PS5 Slim (EDM-140) powers on with beep + blue LED for ~2 seconds, then shuts off. No second beep. PSU / basics • PSU tested standalone: 12.15 V stable • 12 V remains stable on motherboard during shutdown • All fuses OK, HDMI visually fine • Board fully cleaned...
  10. S

    Hardware PS5 CFI-1016A strange problem. Blu light, start then white light 3 beeps and shout down

    The LED ribbon cable looks good. Disconnecting LED board the consol starts and work normally. The problem was this tiny LED board. Ordered an other one, board ID code: EDL-010 (my PS5 is 1016A model). Will test it as soon as arrive.
  11. S

    Hardware PS5 CFI-1016A strange problem. Blu light, start then white light 3 beeps and shout down

    Hello people, please let me describe my problem: I purchased this not working PS5 CFI-1016A. Out of warranty, seller says that actually brought the consol to the local repair shop but they din’t solve. I had not opened it yet to ispect the inside. This is the strange problem: as soon as I pluy...
  12. S

    Tutorial PS5 Exploit Guide

    Just asking. I fixed a Ps5 FW 22.02-06.00.01.42-00.00.00.01. This is not exploitable, right?
  13. S

    Hardware Debugging faulty BCM4356 / orange screen / boot loop

    This is my story: My switch WiFi/BT IC has failed, then I replaced with one purchased on AliExpress. Now WiFi it’s working good but BT does not, can’t connect to anything. Usinig Linux L4T distro both WiFi and BT are working good, It does detect and connect to joycon and network. This point me...
  14. S

    Hardware Debugging faulty BCM4356 / orange screen / boot loop

    Any news in reprogram this IC?
  15. S

    Nintendo Switch 2016 stuck at second boot logo (nintendo switch logo) fast charge working

    It seems like Ubuntu does not detect any WiFi card, is that right?
See more