Recent content by sin89rus

  1. S

    Ps5 migrating APU from edm 030 to edm 010 board.

    Yep, exactly. Maybe NOR partition need for someone who has dead NOR, but don't wanna loose data via reinstall system. Anyway, i will check 61 SB with original EDM-020 NOR on EDM-031 when get 61 SB. But think nothing change, just want to be sure, don't know maybe Cxd90060agg don't meet with 69...
  2. S

    Ps5 migrating APU from edm 030 to edm 010 board.

    What do you mean "boot fine"? Its BLOD like original edm-020 was. Its just test for dead apu, and its dead. But i shure it will be work ok, if apu ok. Apu have like 12ohm for zen2 core (like 2cer more than working ones EDM-020). I just want to test it for 100% and now its done. NOR was just...
  3. S

    Ps5 migrating APU from edm 030 to edm 010 board.

    I just wrote it, don't i? You can translate my messages and get image about situation in your head. https://vlab.su/viewtopic.php?f=202&t=146830
  4. S

    Ps5 migrating APU from edm 030 to edm 010 board.

    The answer for my question - nand need same wifi as donor board has, cause wifi firmware inside ssd (if you, of course, can't swap it) and if its misscompatible ps5 even don't show the BLOD, just beep. After added 1.8v rail to edm-031 and j20h100 instead j20h104 - all work perfect, dont need to...
  5. S

    Ps5 migrating APU from edm 030 to edm 010 board.

    After migrate apu+nand+tmp without any nor modifications the mobo pass initialization with blod or write nand errors (cause bios and nand info misscompatible) and just beep? Did the same, but edm-020 to edm-031 to check apu for dead state, but get nand errors, with edm-030/31/33 nand all ok...
  6. S

    What happened to hwfly's official firmware?

    wow, thanks my man, after update hwfly lite 4.2 from ali to 0.7.1 firmware i get infinity training sessions, tried all firmwares (spacecraft / hwfly 0.6 / firmware from old ali seller hwfly 4.0) - same. Only original 0.3.1 and original bootloader backup fixed situation, seems like not all chips...
  7. S

    Tutorial How to flash the HWFLY Clone chips

    Just few moments ago tested with new switch v2 - all ok. Put 0.7.1 firmware of HWFLY-NX to SD and after start it's run immediately update. After - retrain again - and now i have SpaceCraft-nx bootloader with HWFLY-NX firmware. All perfect, can reset trainings with hwfly-toolbox. So what better...
  8. S

    Tutorial How to flash the HWFLY Clone chips

    why? just google "space craft nx github" and flash it with gdlink programmer or st-link utility. I don't know nothing about clones HWFly, but know that: when its trained, its can't start another switch, so you need to delete trained parameters with toolbox payload, or short two contacts before...
  9. S

    Tutorial How to flash the HWFLY Clone chips

    I replaced my original SX Core MCU with new cheap 1.5$ gd32f350 Flashed Spacecraft-NX, bootloader to 0x08000000 firmware to 0x08003000 with GDLink (stlink work too) And now USB detected my SX Core and it work good. So, MCU is problem, its very cheap to replace it and get fully working chip.
  10. S

    Tutorial How to flash the HWFLY Clone chips

    main ic probably, i will wright here if replace and flash via swd help. still waiting mcu like i said update with usb sucks. Should use update payload on NYX instead. Yesterday i was flash OLED chip via update payload succesfully. REMEMBER, forget about USB update of chinesy chips, however i...
  11. S

    Tutorial How to flash the HWFLY Clone chips

    yep, already thought about. Ordered 2pcs (1.5$ each) and will try to flash, hope its not dummy for 1$. i suppose its my fault, when i tried to flash via USB its stuck, and i cant wait some s... like this cause life is so short and just unpluged.
  12. S

    Tutorial How to flash the HWFLY Clone chips

    Is anyone can explain to me simple thing? SWD via ST-Link / UART via USB TTL (like manual describe) - both do same thing? Or UART do with exta and can do what SWD can't? I flashed my SX Core 1-6 via USB and its bricked, i flashed it via SWD with Spacecraft-NX second release and it's boot in...
See more