Recent content by Siedlik

  1. Siedlik

    Hardware Nintendo Switch not charging

    I don't have a camera with good zoom, but its next to M92T36 in right bottom corner.
  2. Siedlik

    Hardware 3rd party dock not working

    It didn't brick it, both consoles still works on the original dock. So the question is, is Nintendo blocking 3rd party docks or something is wrong with them.
  3. Siedlik

    Hardware 3rd party dock not working

    Hello, I have bought three 3rd party docks and 3 of them dont work on my switch. I tried one of them on family switch and its also not working. Both switches work on the original dock.
  4. Siedlik

    Hardware Switch will charge and work fine, but does not display on TV in dock

    Here you can find some more info about the USB ic https://www.tronicsfixforum.com/t/info-board-diagram-and-part-numbers/91 Did you check for any shortages around the PI3USB ? Did you check the USB PORT inside ? Are you using the original dock ?
  5. Siedlik

    Hardware Nintendo Switch not charging

    Its fixed. When replacing the M92T36 I moved one of the tiny caps on bottom right, and when I tried to move it back I broke it. It ought it was good idea to just bridge it :D Removed the bridge and its working. But the FAN didnt work, so removed like diode next to the connector and its working...
  6. Siedlik

    Hardware Switch Lite not charging

    What size are they ? Bought some from eBay 220k but they are to big :D
  7. Siedlik

    Hardware Switch black screen

    Do you have a multimeter ? Check battery voltage or check if the cable is giving the voltage to the motherboard.
  8. Siedlik

    Hardware Nintendo Switch not charging

    Thanks for that, looks like the grounds are correct. USB-C is getting power, sends it to M92T36 and then it goes to BM92T30 M92T36 recognize the cable, but does not take any amps from charger Will try original charger and add some extra solder to BM92T30
  9. Siedlik

    Hardware Nintendo Switch not charging

    Will try that, also would the switch charge from a 5v source ? Would that be enough to keep it alive ? Also, with M92T36 should few pins be shorted ? I got like 3 pins shorted, 2 of them are going to the small resistors and the 3rd short is on the dot side first from the right. I think that...
  10. Siedlik

    Hardware Switch Lite turns off after Nintendo logo,some short issue

    Minus should be shorted, not sure about the middle one. On my normal switch middle one is not shorted.
  11. Siedlik

    Hardware Nintendo Switch not charging

    I have put the new battery, console is now turning on all the way. Im getting charging logo, but its not charging. Its only 5v and on amps. Last chance is with charging IC. - Charging IC changed still not charging Would USB cause it not to charge ? Even if its getting the voltage ? It was...
  12. Siedlik

    Hardware Nintendo Switch not charging

    I was able to replace the LCD connector successfully with hotair and $8 amazon USB microscope :D Switch is turning on now, but still showing LOW battery and goes off. With USB connected im getting 4.9V as on the image and with battery connected im getting only 3.2V around charging battery IC...
  13. Siedlik

    Hardware Nintendo Switch not charging

    I got the USB VOLTAGE - AMP meter. Just checked the M92T36 and one side didn't have enough solder, so I added a bit more and it looks better. But still not charging, checked the voltage with battery connected and the fuses around the charging IC were getting between 2v and 4.9v. It could be...
  14. Siedlik

    Hardware Nintendo Switch not charging

    Hello, Bought switch that don't charge. Firstly the port was damaged, so I replaced it. After I replaced the port, there were shorts around M92T36. After replacing M92T36, the shorts were gone, but I'm not getting "No continuity" on those small resistors as on attached image. The switch was...
See more