Recent content by Nindando

  1. Nindando

    How do I check IMU voltages on switch lite?

    could someone help me with this or is there a guide?
  2. Nindando

    Motion controls not working on switch lite

    My motion controls aren’t working. I checked the diode values and they’re all pretty close but are they too far off? #4 and 7 are not connected. Is there anything else anyone can think of that I could check or troubleshoot
  3. Nindando

    Switch lite as card reader failing to init sd card

    This pin is giving no diode reading. Neither are these two (not sure how to tell the difference between capacitors and resistors). Would replacing them be an easy enough fix or is this indicatatong a deeper issue?
  4. Nindando

    Modded switch won’t boot OFW

    It ended up being something with the fuses. I was able to unplug the chip, boot once normally, then plugged the chip back in and everything has been working as expected
  5. Nindando

    Modded switch won’t boot OFW

    I can get to OFW by launching from hekate but from power off I can’t boot OFW by pressing power with vol+ and vol- pressed. It doesn’t actually bother me but it doesn’t seem right so I wanted to check if I should worry about it or just keep going. Is this an indication of a future problem or a...
  6. Nindando

    "NSP Forwarder Generator" - An online tool to create NRO/RetroArch forwarders

    This is awesome, thank you! Does it still work? I'm getting "The software was closed because an error occurred.". Nevermind, got it. sorry. I had the path wrong. Great job thanks again!
  7. Nindando

    Homebrew Homebrew app Switch Lite Dock with Raspberry Pi and SysDVR

    Would raspberry pi 5 be better now that it’s out?
  8. Nindando

    Please help with troubleshooting bad Picofly install

    That’s a good point. Yeah it doesn’t turn on with the orange flex cable plugged in and sometimes it turns on with the apu flex plugged in. I’m not sure why. I think I’ll have to remove the orange flex cable. Thank you for all your help! I was totally stuck a few days ago!
  9. Nindando

    Please help with troubleshooting bad Picofly install

    This is a good idea. I tried it and there was no blinking light which means it’s not getting 3.3v Sorry I meant to say I turned it on too and no reading through my solder here but I did get one of 3.3 from the square pads by the right of the chip that the guide showed to try Then, I tried...
  10. Nindando

    Please help with troubleshooting bad Picofly install

    No the picofly doesn’t light up when I power up the switch and yes that is the flex cable that came with the switch 1760016740 Could I add a wire to this set up? Keep everything as it is but then just attach a wire to any other 3.3v spot on the board? Or try to use this same capacitor I’m...
  11. Nindando

    Please help with troubleshooting bad Picofly install

    I got home and checked the chip with power, it did one blue flash then three green flashes which makes me think it’s flashed I hit the 3.3v again with solder I checked and got continuity from the C, A, D, B, 3.3v and ground points on the flex cable to the corresponding points on the chip I...
  12. Nindando

    Please help with troubleshooting bad Picofly install

    I think it’s worth the wait. Everything really did line up perfectly. My problems seem to be with my limited experience and skill, not the flex cables. I know there were some bad batches of these orange ones so before you start I’d just double check that the 3.3v and b lines are feeding the...
  13. Nindando

    Please help with troubleshooting bad Picofly install

    Thank you this is great! I have a lot to check when I get home tonight which is what I was hoping for. One questions so far though, on the 3.3v, I’m only connecting it to the close end of this capacitor right?
  14. Nindando

    Please help with troubleshooting bad Picofly install

    This is my 2nd attempt at installing a picofly chip on a switch lite. Nothing happens when I press power with chip plugged in. When I unplug chip, console boots regularly. All readings on multi meter seem good Chip is flashed I have tried two chips
  15. Nindando

    Hello

    Thanks for everything! This site has been really helpful
See more