Recent content by neontiger

  1. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    The problem turned out to be that I was pushing the hekate payload instead of fusee-primary. Everything was working fine afterwards, including some older applications that appeared the same error as tinfoil after installing. What's the difference between those two payloads?
  2. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I've copied the unpacked folders and merged them into the atmosphere folder. The 2 new folders inside atmosphere contain the sigpatches.
  3. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I've updated the sigpatches but the error persists. DBI works fine although a bit slower than awoo (15 mb/s from 33-45) and some apps (mostly old ones)) that I've tried to install are installed successfully but do not open from the home menu (same error message as tinfoil)
  4. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Thanks a lot, but tinfoil keeps on giving 'could not start software' errors. Does it have to do with the sigpatches?
  5. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I've edited the original message with the quote, for some reason it wasn't included in the quick reply section on the bottom of the page. I didn't upgrade my emuNAND since it wasn't mentioned in the setup guide that I've followed, once I've figured out it was necessary I've upgraded to 16 and...
  6. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    No specific reason to run in 4.1.0 this is just my sysNAND and since I'm a newbie and the guide I've followed doesn't mention updating the software I didn't do it. I'll proceed with that and let you know if the software works.
  7. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I 'm trying to install .XCI or .NSP files through USB due to file size (considerably over 4gb given the FAT32 formatted sd card) but nothing seems to be working. I've set up my sd card files using NH Switch guide. This guide does not contain the 1) sigpatches which I've put later, 2) fusee.bin...
  8. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I'm actually trying to install an .XCI file, but I guess it shouldn't make a difference. The patches have to be downloaded from eXhumer's GitHub repository, right?
  9. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Is there any detailed guide on how to install applications with TinWoo Installer. I've tried to upload with ns-usbloader but I get a failed to install error, so I would like to make sure I'm doing everything the right way.
  10. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Whenever I launch TinWoo Installer I get a prompt about hbmenu running in Applet Mode. Should I disable this? I don't have any installed titles yet.
  11. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Pretty much ended up looking up for USB install instead. Any suggestions for XCI installations? I think I've came across solutions only working with NSP, but might try ns-usbloader.
  12. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    TinWoo does not recognise files split and trimmed with java-xci-splitter, right?
  13. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I'll try to install it, thanks. I know but I don't get the installation screen (loading folders etc.), instead the screen blinks for a couple of seconds and Tinfoil is not found on the home menu.
  14. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I can't launch Tinfoil from the hbmenu, pressing/clicking takes me back to hbmenu. Any thoughts?
  15. N

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Updated with Daybreak to 11.0.0 using the FAT32 only option. I guess the controller update prompt on start is safe to do?
See more