Recent content by nalex7752

  1. nalex7752

    Hacking SWITCH NOOB PARADISE - Ask questions here

    i had to scavenge trougvh some dead pcbs i had laying around but i managed to find some 55 ohms resistors, now its boot fine! Thanks buddy^^
  2. nalex7752

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Picofly
  3. nalex7752

    Hacking SWITCH NOOB PARADISE - Ask questions here

    HI all! I’m having an issue where my switch oled boots into emu-nand but not ofw/cfw sysnand. I’ve already tried creating a new emunand and dumping the nand again, and everything seemed to go fine. The console was booting into ofw without any issues prior to installing the modchip. My fuse...
  4. nalex7752

    Switch boots emu-emmc but not OFW/CFW SYSEMMC

    Basically title I already tried to create a new emuemmc/dump the nand again and everything went fine. Console was booting ofw prior to install modchip no problem. Fuse info says: 20 | 0 - HOS: 19.0.0+ Do i need to use emmchaccgen? Thanks^^
  5. nalex7752

    Help with the Instinc v6 post-installation

    Yeah, totally! I mean, im not new to soldering but its my first time doing something on a switch so could absolutely be! Anyway, thanks again, ill check another time my soldering and ill post it back if i find any other problem. But, do i need to update the firmware on the chip? Is there a...
  6. nalex7752

    Help with the Instinc v6 post-installation

    isnt the B point actually just a GND? Should I try another ground on the board?
  7. nalex7752

    Help with the Instinc v6 post-installation

    I got the chip off AliExpress, but I don't know if it's preflashed. I found a guide here for flashing, which involves soldering directly onto the chip. However, I have a microUSB breakout that I believe could be used for updating. Is it as simple as plugging in the 'dongle' and dragging and...
  8. nalex7752

    Help with the Instinc v6 post-installation

    I read that this modchip quality isnt that great and to pay attention to not add to much solder on the chip pads as it could easily short on the ground of the chip. Btw thanks, ill redo all of my soldering.
  9. nalex7752

    Help with the Instinc v6 post-installation

    Yep, I did the installation I'm not at home at the moment and I only got this image.
  10. nalex7752

    Help with the Instinc v6 post-installation

    Hi all, i got this Oled with the instinct v6 installed but i cant recognize the led sequence. tested all the points, the readings are: 3.3v .718 - D .632 - A .549 - C .553 - On the D point i cant get a reading, but i read that some multimeter (like mine cheap AF) cant get a good measurement, i...
  11. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Xeno was the problem, replaced with a clone one and it works perfectly. You can close the thread. Thanks all!
  12. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    avrdude command with the reset grounded
  13. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Did it, but, is it normal that avrdude wont recognize the chip? The power led wont event turn on.
  14. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    Currently trying to reflash it via avrdude but without luck. I've found this site https://kyleglisso3.wixsite.com/moddedgear/mods but i can't get the program find the Atmel. I know that the solder aren't the best this time maybe because it's pretty late. I'm gonna try again tomorrow, let's see...
  15. nalex7752

    Hardware [Nintendo GameCube] Help needed installing Xenogc

    the pal game that i have is working fine, the ntsc-j or the swiss dvd did not boot at all
See more