Recent content by Muta

  1. M

    Hacking SX lite no CFW, boots to ofw

    surely related but i finally figured it out. So i reassembled it after i posted this and it worked for some reason, going to cfw easily. After about 2 weeks it stopped booting cfw, same white light. opened it up resoldered wires again for 2 hours troubleshooting., even flashed the chip fw1.3...
  2. M

    Hacking SX lite no CFW, boots to ofw

    yes, i even tried reflowing as i said, completely unplugging the battery Ill try this, just found the firmware and flash tool on SX's site.
  3. M

    Hacking SX lite no CFW, boots to ofw

    Cant figure out what went wrong. SX Lite has been running for a month fine now, I reboot and now it boots straight to horizon ofw without any TX boot logo or anything. it will boot without SD as well. LED flashes blue 3 times then quickly goes to white. After powering off, it does this a few...
  4. M

    Hacking SxOS BOOT.dat? Error?

    Have you removed the shell at all? Make sure the sd reader is seated well. Also make sure your SD card is not formatted as ntfs.
  5. M

    Hacking Can you update a banned switch

    Yes, easily update offline: https://switchtools.sshnuke.net/ ChoiDujourNX
  6. M

    Hardware Are revised (unhackable) switch units in the wild yet?

    They have been out since july
  7. M

    Hacking Question Tinfoil Failed to install NSP

    Make sure the name isnt too long. I.e. rename it to something like "game1 update.nsp:
  8. M

    Hacking SXOS v1.5 FTP Help Required

    if you dont know if you are on the same network, honestly you should not be trying to FTP stuff... either way, same network is exactly what it sounds like, connected to the same SSID/Router
  9. M

    Hacking Question Is it safe to remove the metal cover?

    It does direct air flow, it may cool the CPU a tad, but that is what the copper heatsink is for.
  10. M

    Hardware Switch opening tools

    https://www.amazon.com/gp/product/B06Y2N568J/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 all you'll ever need.
  11. M

    Hacking RELEASE Nintendo Switch Trinket M0 External Dongle Build Tutorial / Modchip

    You should have a 3d printed brace for the USB connector. For me, i would not trust pushing it in over and over, something will break, even with that big ground point. either way, good tut. Im going to still keep mine internal :)
  12. M

    Tutorial Trinket Internal Install.

    No. I am going to replace the M92T Usb controller IC in a few days, i think i fried that chip. Ill post here if it works after the replacement. did you happen to forget to unplug the battery before soldering?
  13. M

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    you have a pic?
  14. M

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    You are using too much solder. Literally all that will stick to the end of the lead is enough. More and it will stick to other things.
  15. M

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Heres some pics of the other 3V route i used, it is easier(at least for me) than trying not to bridge the connections between the 2 caps. pic 1 after using X-acto to bare the trace pic 2 after tinning the trace pic 3 after attaching wire and gluing the wire so it didnt pull off. pic 4 is the trace
See more