Recent content by Modzvilleusa

  1. Modzvilleusa

    V2 Switch. Black screen after Launching from Hekate.

    Sorry for leaving you guys hanging here. Totally thought I responded. It was a goober oversight on my part. I got pigeon holed into thinking it was a software issue. Eventually I removed the cpu flex and realized that multiple caps between sp1 and sp2 were bridged / shorted out. Since it was...
  2. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    I can confirm this is the standard Oled wiring. I've run into many headaches using those emmc flex cables I'd recommend wiring it up manually like this one pictured. 36awg ftw
  3. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    When you run the nuke.uf2 to blank the chip, you plug it in via ubs c with the console off and it's instantly detected, console doesn't seem to turn itself on. Dragged over the picofly.uf2 it flashes then the console turns itself on. Power down, turn it back on and the chip trains / boots. I've...
  4. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    If the Usb pinout is the same for Oled, this should be the setup for Oleds on the top side.
  5. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    I think it's massive. installers can test then blank out the chip. Users could then plug it into usb on their end and flash it.
  6. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    fantastic thanks! Will test on a lite asap and report back. couldn't get it figured out on an oled. v1 worked fine though.
  7. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    What about wiring the button to vol + or -? I spammed that button on the pico after the console booted and it didn't seem to have any effect. Also, does anyone know where the D+ and D- points are on a lite?
  8. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    Yeah I don't see why that wouldn't work. if it's not blank you'll need to sort something out for the button that you likely removed
  9. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    Welp turns out it works exactly like that. I wired up d+ and -. held the button on the pico, pressed power and boom. I can write to the rp2040 over the switches usb c port. This is huge! now if the chip is blank, no button will need to be held. It should just come up on windows.
  10. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    These boards are fantastic
  11. Modzvilleusa

    Corona 4gb Emmc to 16mb nand conversion guide.

    Just finished a video guide on how to pull this off If a decent bit of work but the hardest part was piecing all this information together. I wasn't finding any proper guides when searching. Most of the information came from an old stream from sharkys customs, various comments in reddit /...
  12. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    the pads are behind the flex cable in the first pic. 1684562875 pink screen is usually a damaged cmd resistor on oled. Check that the resistor measures 4.7k ohms rp2040 will throw a slow emmc error if there's no 47ohm resistors on cmd clk and dat0. maybe these boards are missing those added...
  13. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    It looks like a similar setup to the trinket m0 which has the ability to be reprogrammed over the switches usb down the line. It's just these two wires that handle that afaik. I don't see why the same couldn't be possible with the rp2040
  14. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    I'll consider it for sure. I have so many videos I want to make but finding the time to do it has been challenging lately.
  15. Modzvilleusa

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    I have a couple of these ordered and I'm looking forward to playing with them. I'm super interested in that little + and - up top. Should be usb passthrough for programming / debugging over the switches usb c port. I also managed to get my hands on one of the lite versions of these chips.
See more