Recent content by mmedeiro

  1. M

    Best way to install NSPs?

    Any idea how to enable 3.0? I tried usbc to usbc but it only show 2.0. My Atmosphere config looks like this. [usb] ; Enable USB 3.0 superspeed for homebrew ; 0 = USB 3.0 support is system default (usually disabled), 1 = USB 3.0 support is enabled. usb30_force_enabled = u8!0x1
  2. M

    Trustworthy HWFLY installer needed

    Hi all, Im looking for a trustworthy HWFLY installer. I was skinned by a member here for $830 for a premod and an install on my current console. Moved on. Now im looking for an installer for 2 oleds, both with the HWFLY v4.1 chip. Please reach out. Thanks,
  3. M

    Nintendo Switch OLED - help with component

    Anyone know the value of this SMD resistor?
  4. M

    Hardware Repair specialist?

    Hi, Do we have a resident repair specialist? My repairs are beyond my experience and im willing to pay a professional to clean my 2, now broken switches up. Any info would be helpful. Thanks
  5. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    I think i need to go from the legs of the USB C port to the ports on the back no? Which legs on the USBC are D+ and D-?
  6. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Looks like the SD port on the board had a loose pin. I desoldered the pad and I'm waiting on the new one to arrive tomorrow.
  7. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Got home and the Switch just started working again, same as the Mexico trip. So bizarre.
  8. M

    Hacking Failed to init Emmc in Atmosphere but stock FW works fine

    Hi all, When booting into Atmosphere via RCM I get the, "failed to mount Emmc" error. When I boot directly into official FW the console boots no problem. I have a Trinket M0 installed and its been fine for a 2 years now. This happened when I went to Mexico but then resolved on its own and now...
  9. M

    Hacking Switch with AutoRCM won't accept payload

    Interestingly my Trinket M0 just stopped injecting the payload. Switch goes in to RCM mode then I have to manually inject with the TegraRCMgui. Not sure what could have happened, was working fine for a year or so.
  10. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Yup, so now i just need the point on the front.
  11. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Yea I lifted those, so now I need to solder a bridge between the chip above those pads then to the rear of the PCB. I need all 4 of the points... I think its the two middle pins above on the 6 pin chip above the lifted pads, and I'm not sure of the 2 locations on rear. This was my original...
  12. M

    Hacking How to repair lifted D+ and D- pads above USB C port

    Hi all, I lifted the two pads data pads D+ and D- during a trinket install, does anyone know how to create a bridge? I know there was a diagram but I cant find it anywhere on here. Thanks,
  13. M

    Hacking Console not entering RCM

    Hi all, long story short i broke the LCD connector on a switch, so the screen is dead. It also had the right joycon not detected in handheld mode which i fixed by replacing the rail. Now it detects the joycon. Issue is; it's not entering RCM with a printed jig I purchased on Amazon. I have...
  14. M

    Hacking Switch not booting past the Nintendo logo

    Sorry for not updating. Fat32, had to reformat to exfat. thanks
  15. M

    Hacking Trinket M0 install troublea

    Hi, my response was to Harmony United. lol.
See more