Recent content by MentendoSnitch

  1. MentendoSnitch

    would i get ban for transfer save from a modded switch to a switch2

    We still don't have evidence of that with data from Switch to Switch 2, but a lot of people got banned Just for getting saves or game card dumps from banned consoles on Switch. So it Is very likely that data coming from banned consoles or just from not an official source get somehow "marked" in...
  2. MentendoSnitch

    Hacking Nintendo switch V2 picofly issue

    No worries m8, happy that your issue is solved!
  3. MentendoSnitch

    Hardware Switch OLED missing resistor near the cpu

    Hi everyone, I was fixing a Nintendo Switch OLED of mine and I've found out that It was missing a resistor. Can anyone tell me its value?
  4. MentendoSnitch

    Hacking Nintendo switch V2 picofly issue

    Hi, that's not exactly the right way to ask a question here. You should open your own thread where you explain the issue, the console rev (V1, V2, OLED), the kind of mod (if picofly install or v1 mod via fusee). If you got a Picofly install It could be useful to have sono photos of the install...
  5. MentendoSnitch

    Hacking I've got Slow EMMC issue after Picofly install, boots both CFW and OFW

    Sorry for the infinitely late answer. I simply got informed on how the data lines work: you got to make them work with the lowest resistance you can, so I generally start with 47Ohms on Clk and 100 on cmd and Dat0, then i raise resistance levels if i got errors, i suggest to keep around 220ohms...
  6. MentendoSnitch

    Hacking Nintendo switch V2 picofly issue

    It Always boots fine ofw, when it boots fine cfw hekate shows emmc at full Speed (400mb/s) and no partition errors, I also noticed that It usually works when the console Is off from a long time (some hours/a day), i don't know if somebody got this kind of behavior before. I tried different...
  7. MentendoSnitch

    Hacking Nintendo switch V2 picofly issue

    I've got a V2 Nintendo Switch with picofly which gives me 90% of the times error =** and 10% of the times boots perfectly fine, i Just can think at insulation problems, but i would like to have some opinions, i modded a lot of V2 in the past but never had an issue like that, tried the...
  8. MentendoSnitch

    Hardware Accidentally Removed Resistor Below The RST Solder points

    I'm asking myself if It could work the same installing the resistor directly on the emmc board on the same line and linking the other end to a gnd (on V1/V2 board), I've got a resistor of the right value but not of the right size, let me know your thoughts, please
  9. MentendoSnitch

    Hacking Switch stuck to ofw boot after updating ofw

    It could create a problem of incompatibility between EMMC and Emummc, since they're set on different fw versions, when It comes to Major updates the problem becomes even bigger, I would always suggest to update both of them, starting from CFW and atmos/Hekate, then update the OFW, in some cases...
  10. MentendoSnitch

    Hacking Switch stuck to ofw boot after updating ofw

    If you updated your Switch to 19.0.0, since it's a major update, as you can read in Atmosphere's GitHub Page, It breaks Atmosphere, so you should update Atmosphere, Hekate and fusee to make it work again, if after the update It still boots only in OFW, there could be problems in the installation...
  11. MentendoSnitch

    Hacking switch keeps booting to OFW

    Maybe Is Just a dumb intervenction, but have you tried moving the plastic switch on the side of your SD Adapter?
  12. MentendoSnitch

    Hacking I've got Slow EMMC issue after Picofly install, boots both CFW and OFW

    The new resistors came here this afternoon, I tried tons of combinations of them on CMD and DAT0 points, but still Hekate detects the EMMC in Slow Mode (200mbps this time, so I assume that a half of the data lines should be working now) and I can't boot to OFW, getting "Unable to read pckg1"...
  13. MentendoSnitch

    Hacking Hardware Modded switch doesn’t boot after injecting emuMMC phase

    So Happy that it's working again!
  14. MentendoSnitch

    Nintendo Switch Prodinfo question

    That's probably because of exosphere.ini, which makes your sysMMC prodinfo blank, try to open the exosphere file from your PC and replace the "1" at the voice "blank_prodinfo_sysmmc" with a "0" and see if your serial number comes back again, if It doesn't, you probably Need to rebuild the nand...
  15. MentendoSnitch

    Hacking Hardware Modded switch doesn’t boot after injecting emuMMC phase

    The blinks show that the chip Is glitching Just fine, so the problem Is very likely software, particularly of your SD card, what SD card are you using? Is It formatted in FAT32? It could even be that the EmuMMC was corrupted during the writing sequence, try to format It and install on it a...
See more