Recent content by living

  1. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I get these screens (hekate) to appear but it does not load anything in the micro sd I have this: [atmosfere] [Nintendo] [sept] hbmenu.nro What escapes me? thanks
  2. L

    Tutorial Trinket Internal Install.

    Hi from Spain, the Files to send at chip, where are contained. I have 7.0 firmware and months ago, in 6.02 its perfect ...
  3. L

    Tutorial Trinket Internal Install.

    ok, now I get it started in heckate, but once it does, as I start the homebrew, I give it to the photos folder and it does not do anything ... I'm in 6.1
  4. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I'm going to do it according to your installation scheme but I have a question, if I want to use hekate. what file injected in trinketboot and what in switchboot? since there are 2 files normally, some weigh a little kbs and others like the current.uf2. it weighs 512 kb my question is: what...
  5. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I'm having difficulty for the pc to see the units, both the TRINKETBOOT, as the SWITCHBOOT, and that the thickness of the VCC and GND is higher than the other cables. I am following this scheme that I upload, and since I want dual boot, I am not using the brown cable that it puts (vol + strap)...
  6. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I do not understand. Something should be in the micro SD not? regardless of the tinfoil, homebrew, etc softwares, I mean the basics to boot hekate .... that is put in the microsd
  7. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    THEN if I want to use hekate what files do I have to put in the micro sd?
  8. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Oh ok, then I remove folder 0, since I'm going to use Hekate. I inject the 2 files true, the [Version_1_trinket_rebug_joycon_only.uf2] in the TRINKETBOOT and one of these 3, [4A3C_Trinket_Rebug_mode1], [4A98_Trinket_Legacy3_mode1.UF2], [4A98_Trinket_method3_mode1] and is there included hekate by...
  9. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    TO FOLLOW YOUR STEPS, Once those 2 processes have been completed, what files do you have on your SD memory card?
  10. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    hi i am also having problems to program the chip, could you tell me the order and the files that you used for the programming of the TRINKET M0 chip? I can not do it, thanks
  11. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    once the TRINKETBOOT is closed, when entering the CURRENT, is the SWITCHBOOT or REBUGBOOT automatically opened? if I wait it does not appear, but if I give RESET wait 1sg RESET, it does not appear ... I can not visualize that unit ...
  12. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I used AWG24 cables for the GND and for the VCC and it does the same, I can not get into the SWITCHBOOT or REBUGBOOT mode ..... I only enter the TRINKETBOOT
  13. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    to see I drag the CURRENT.UF2 to the TRINKETBOOT ..- and when overwriting the file that was, the unit is closed, indicating that it has been recorded, but it does not give me the option to open the second unit to write the chainloader. if GND were bad, the TRINKETBOOT would not open either?
  14. L

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I can easily access the TRINKETBOOT with a double click, then I drag the CURRENT.UF2 file but then I can not find the SWITCHBOOT or REBUGBOOT unit, the same TRINKETBOOT unit appears again, I try to wait 1 sg between pressing and pressing. but the same unit always appears .. (to say that the...
  15. L

    Hacking Nintendo Switch with trinket installed

    but what do you mean that .nsp can not be installed as before? Should we modify them in some way? only the SX OS works?
See more