Recent content by Joaoaug

  1. Joaoaug

    Hacking Question Any progress in hacking the patched switch?

    This thread was dead for almoast a year before it was brought back to life... the OP probably has hacked or updated his switch a long time ago
  2. Joaoaug

    Hacking Frying the Switch

    When I was modding my joycon (soldering a Reed switch to it) I accidentally shortcircuited it's motherboard while trying to remove the battery cable with a metallic twizzler. After some research I found out that there were some fuses (0 ohm resistors) that were burned. Since the joycon has this...
  3. Joaoaug

    Gaming Free eshop?

    you will need emummc, if you plan to use athmosphere, or emunand if you plan to buy sxos. There's some guides in the guides section. If you dont wanna to mess with files and folders go with sxos, if you dont wanna spend some money go with atmosphere. After setting up your emunand or emummc find...
  4. Joaoaug

    Hacking Emummc And Sysnand Help noob

    i did something similar to that a while back, and think that my experience might help you a little I started using CFW as soon an it got support to FW 4.1, since we didnt had a emunand backthen my sysnand was as dirty as it could be, but i have made a bkp when it was clean. when smash cameout i...
  5. Joaoaug

    Hacking Atmosphere crashing after updating sysnand to 9.0.0

    Tks mate, i just got acess to my emunand again.
  6. Joaoaug

    Hacking SX OS - Creating emuNAND and cleaning NAND

    You'll need to reinstall your games. When I made my emunand all the games that were installed on the SD card were erased.
  7. Joaoaug

    Hardware HOW TO AVOID RIGHT JOYCON UPDATE

    After the update you just need to reboot the joycon, but the permanent bridge on pins 9 and 10 for some reason don't let it reboot. Looks like updating it via bluetooth is one way to bypass this issue. I think that in your case the joycon might have run out of battery and when you docked the...
  8. Joaoaug

    Hardware HOW TO AVOID RIGHT JOYCON UPDATE

    Great, if you need help just give a shout.
  9. Joaoaug

    Hardware HOW TO AVOID RIGHT JOYCON UPDATE

    If you have some skill with the soldering iron it's really easy and fast to remove the bridge between pin's 9 and 10. Just open the controller(4 Y screws) and disconnect the ribbon cable that goes from the rail to the circuit board (to prevent any damage to the board) then remove the extra stuff...
  10. Joaoaug

    Hardware HOW TO AVOID RIGHT JOYCON UPDATE

    There is only one kind of joycon mod that makes it "unsusable" after the update, that would be making a permanent conection of the pins 9 and 10, usually it's done by soldering a wire or some resistor. If that is your mod, after the update you will need to remove the baterry of your joycon and...
  11. Joaoaug

    Hacking FOUND my virgin rawnand, have never turned off Airplane Mode since first RCM/CFW boot

    This weekend i Will do the same, my smash should arrive in 4 days and i want to make my switch ready to go online. There was 1 episode of my switch going online with ofw um the early days of Pkmn Lets go, my wife booted on OFW and tried do play. I dont know it i am banned already because of that...
  12. Joaoaug

    Hacking Sx os 7.0 fuses

    Just to be sure, if i boot the OFW via sxos(or hekate) it wont burn my fuses or if i boot OFW will always burn the fuses?
  13. Joaoaug

    Homebrew RELEASE XLink Kai 7.4.32 released with Nintendo Switch LAN support

    Tks for your hard work. I'll test it as soon as possible.
  14. Joaoaug

    Hacking Planning to hack Switch. Dongle suggestions?

    That's a great choice. I use my phone to inject the payload, but a friend has this one and i really liked it. I have 2 cons about it 1- the size, it is huge. 2- you need to install a program to add a new payload to it.
  15. Joaoaug

    Hacking 6.1.0 ChoiDujour Switch is Dead ???

    While on CFW or OFW?
See more