Recent content by JackFrostSMT

  1. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    After doing the mosfet by itself last time, this time with flex was SUPER easy. Got an oled done in about 30 minutes
  2. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Ahhhhhhhh thank you, I got it working now. I got a couple of these xiaos so I'll get acquainted with how to use them quickly
  3. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Ok when programming the seeed xiao I get green and red leds on the usb port leds but nothing on the big led on the bottom
  4. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    I see the diagram for the xiao, but the other thread says bridge pins 1 and 2, however the diagram indicates bridging pins 7 and 8 according to the label on the xiao Edit: nvm ignore my dumbass, i see on an online pinout that the D numbers are whats printed and the P numbers are actual pins
  5. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes, 47 ohm gave me about a 50/50 mix of slow emmc and normal. Don't think thatll fix your wifi issues tho if the console reads emmc just fine. Did you say your wifi issue was on sysnand or emummc?
  6. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Dang, I didn't think of doing my lite's mosfets like that. I have them next to each other but they are both wired separately.
  7. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    If you get red led after programming then do not touch the rgb jumper. 47ohm THT resistor will technically work, but its likely going to be too big to close the console up and I've heard there can be electrical interference with those as they have much more mass than smd resistors.
  8. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    20k on rst is only needed if you have blue then green success glitching but reset right after. So if you have no problems booting then you don't need it.
  9. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Replugging might not have the same effect. You should be getting either a green or red led RIGHT after you program.
  10. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Unlock uf2
  11. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Has anyone tested the XIAO seeed rp2040 with 2.6? Digikey sells for around $5 which is slightly worse than Aliexpress but better than Amazons outrageous $15
  12. JackFrostSMT

    Is Tinfoil dead ?

    I can download just fine.
  13. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    Could also use this instead of trying to build it :p
  14. JackFrostSMT

    Hacking Hardware Picofly - a HWFLY switch modchip

    They are the same fets in the same capacitor positions, just uses different routing for the connector for different chip placement. But all mariko apu is the same with same caps so one could bulk order one type and use it for all.
  15. JackFrostSMT

    Picofly AIO Thread

    Try launching OFW sysnand with hekate and see if it boots. If not, its probably the unlock that failed. I flashed 2.5 and unlock separately
See more